background image

 

1

CONGRATULATIONS... 
 

Congratulations on the purchase of your Superior Windmill. You are now the owner of North 
America’s most superior wind powered aeration systems. Proper maintenance and assembly will 
lead to a long life of service from our products. 
 

 

THEORY OF OPERATION 

 

Under the water’s surface there are aerobic bacteria feeding on organic matter, which consumes 
large quantities of oxygen. When this oxygen becomes depleted, hydrogen sulfide gas is 
produced as a byproduct. This causes the water to turn black and a foul odor similar to rotting 
eggs is given off. When you use a Superior Windmill the water stays aerated preventing this 
problem from happening. Using our double diaphragm (TURBO JET STREAM) pump keeps the 
oxygen level even higher and your water cleaner. 
 
 

CAUTION 
 

1) 

DO NOT attempt to repair or service the windmill on a very windy day. It is too unpredictable 
and dangerous, and you could be easily injured. 

 

2) 

Even in low winds, be very careful when servicing. Be certain that the blade is securely tied 
before beginning any work. 

 

3) 

DO NOT climb the tower while the blades are in motion. The head can turn without warning 
and is very dangerous. Use a ladder to climb the tower that is properly and safely secured. 
DO NOT use the tower members as steps as they cannot safely support your weight. The 
recommended method is to lay the tower on its side for any servicing. 

 

4) 

ALWAYS teach children about the dangers of the windmill and keep them away from it. 

 

5) 

Keep your distance from the windmill in thunder, strong winds and lightning storms. 

 

6) 

STAY OFF the pond ice in winter, as it is thin from the air movement under the surface. 

 

AVOIDING THESE SAFETY WARNINGS CAN RESULT IN 

SERIOUS INJURY OR DEATH 

 

 

WARRANTY 

 

The Superior Windmill comes with 18 full months of warranty from the day of purchase. This 
guards against defects in material and workmanship. You can either return the faulty component 
for repair or you can take it apart yourself and phone the factory for replacement parts. You will 
need to have proof of purchase date and if within the 18-month time frame the parts will be sent 
to you at no additional cost. 
 
PLEASE NOTE: This windmill has been designed for maximum strength however it is possible 
that a severe storm may damage or destroy it. Due to this the windmill should be covered by your 
own applicable insurance policy. 
 
 
 

Summary of Contents for Superior Windmill














Reviews: