Kodak DryView 8150 User Manual Download Page 120

Page: 120 / 178

3-16

7F3319

October 4, 2004

Troubleshooting

Removing Film jams from Area 5

Area 5 consists of the components between the processor drum and the film
exit tray. Jams can occur in this area between the drum and the
densitometer, or in the densitometer. See the figure below.
When a jam occurs in this area

all

films in the imager must be removed.

Jam Area 5

1. Open the hood.

CAUTION

Drum and rollers inside the processor are hot. Exercise
caution when working in the drum area.

2. Clear the jammed film from the processor area (there may be more

than one sheet). If film is jammed in the drive rollers, pull the Plastic
Thumb Tab to open the rollers and free the film.

H200_0009da

Densitometer

Plastic Thumb Tabs

Exit Tray

Processor

Drum

Area 5

Summary of Contents for DryView 8150



















































































































































































Search results

Summary of Contents for DryView 8150

Reviews:

Related manuals for DryView 8150

Brands by name

Popular brands

Kodak DryView 8150, User Manual

Search results

Summary of Contents for DryView 8150

Reviews:

Related manuals for DryView 8150

Brands by name

Popular brands