Kodak 8810 User Manual Download Page 4 | Manualshive

Page: 4 / 38

Kodak 8810 User Manual Download Page 4

ii

Table of Contents

Appendix B: Safety and Regulatory Information

Important Safety Information ...................................................................................................................... B-1
Safety Labels ....................................................................................................................................................B-2
Regulatory and Safety Compliance ............................................................................................................B-3

Safety ...........................................................................................................................................................B-3
Electromagnetic Compatibility (EMC) ...............................................................................................B-3
Noise Emission ..........................................................................................................................................B-5
Disposal.......................................................................................................................................................B-5
China RoHS ............................................................................................................................................... B-6

«
...
2
3
4
5
6
...
»

Summary of Contents for 8810







































Reviews:

No comments