C-Mic : To communicate with Monitor
Camera Lens
LED
Speaker : When visitor calls, the voice from
monitor comes out of the speaker.
Call Button : By pressing the button, the related
house will be called.
Name plate
With hanging up the handset, press button to select the door camera for which you want to set CCTV monitoring function. While screen is
on, press [SET]button for 3 seconds. With mode setting sound ringing, monitoring time of the selected camera changes from 1 to 3 minutes.
Screen is automatically turned off. To cancel this function, follow the same steps as described above.
With hanging up the handset, select the camera 1 or camera2 using monitoring function. While screen is on, press button for 3 seconds.
Mode setting sound rings. Every time you press button, saved bell sounds are output. Select the bell sound you want and press [SET]
button to change the bell sound of related door camera. With mode setting sound ringing, the changed bell sound is saved.
Screen is automatically turned off.
For this purpose, automatic DC doorlock should be installed on the door and connected to camera or monitor.
If you press button during the communication with door, the door is opened automatically.
After opening the door, you may end the communication by hanging up the handset or pressing button.
Instructions for operation
■ Communication with door camera
①
②
③
④
①
②
③
④
Hello
Push the call button. The door camera melody is turned on.
You can hear call sound from all connected monitors, and camera image comes out on screen. (Standby time : 30 sec.)
Pick up the handset to communicate with a visitor at door. In case the handset is used with extended indoor units, press button for communication.
Hang up the handset to finish communication. Communication with door is available for up to 3 minutes.
■ Camera monitoring-Don't need to hold handset
■ Opening door automatically
■ Door Camera Call Melody Selection (5 Melody)
■ CCTV Monitoring (3min)
①
①
①
②
②
②
③
①
②
③
To view the state of door without communication, press button and view the image from door camera 1 through the screen.
To view the image from door camera 2 through the screen, press button once more.
To end door monitoring, press button once more. Door camera monitoring is available for up to 1 minute.
■ PABX Communication
- PABX Communication
※Pick up the handset to communicate with a visitor at door.
■ PABX Call
①
②
When PABX call is received from the other monitor (Using PABX). Please, pick up the handset. Then, communication is made available immediately.
Hang up the handset to finish communication
- PABX call
①
②
※
Pick up the handset and check the dial tone.
Push the house number and the call goes to the house by PABX.
While communicating by PABX, if a call comes from door camera, the monitor will ring and turn on its screen.
Push button and the door communication will start with cutting off PABX call.
Name and Functions of each part
Components of product
Specifications
4 Pin cable for camera 2ea
■ Wire
■
DC 15V Adapter (DC type)
■ A Wall hanger frame
■ The front side
■ The back side
■ The the bottom side
■ The front side
■ The back side
■ Monitor
① Handset
② Speaker
③ Monitor Screen : 4" flat type B/W CRT
④ Power LED
⑤ Set : Setting of special functions Set button
: PABX Button
: Identification and communication with a visitor at door
: Door opening during communication
⑥ Dial button
⑦ Camera connector
⑧ Door opener connector
⑨ PABX connector
⑩ Call volume : 2-level adjusts the call melody and telephone ring volume
⑪ Brightness volume : 2-level adjusts the picture brightness
■ Screw for fixing monitor
■Door Camera
Screws for fixing main
body on the wall
Screws for fixing camera
to main frame supporter
4×10mm
4×10mm
4×16mm
2.6×6mm
Screws for fixing main
body on the wall
Screws for fixing camera
to main frame supporter
4×25mm
4X8mm
[KC-D20]
Finishing rubber
Main body
supporter
Main body
supporter
Main body
supporter
[KC-MB30]
Screw for fixing
camera main
body supporter
Screw for fixing
camera
“L”wench
Screw cap (KC-MB30)
Upward adjusting
supporter for lens angle
Model number
Power Source
Power Consumption
Operating Temperature
CRT
Communication System
Wiring
Mount Type
Dimension
AC90V-AC240V 50/60Hz
DC 15V±1V 1.2A
Stand by 1.5W, Max 18W
0℃ ~ +40℃
4" flat tube
Duplex hadset conversation
Camera : 4 wire (Polarity)
PABX : 2 wire
Surface mount
207(W) × 215(H) × 60(D) mm
Power Source
Power Consumption
Operating Temperature
Dimension
Angle of Lens
DC 12V±1V (Power from Monitor)
Max 3W
-10℃ ~ +50℃
110(W)×158(H)×39(D)mm 96(W)×127(H)×32(D)mm 95(W)×127(H)×34(D)mm 40(W)×120(H)×22(D)mm
Diagonal 120。
(angle adjustable)
※Lobbyphone connection : KVL-C302i, KVL-C303i, KVL-C304i, KVL-TC306i, KVL-TC308i
Diagonal 90。
Diagonal 90。
Diagonal 90。
KVM-340
KVM-D340
Model number
KC-MB30
KC-D20
KC-B61
KC-MB20
MONITOR
DOOR
CAMERA
[KC-B61]
4X25mm 4ea
3X8mm 1ea
1
2
3
10 11
4
7
9
8
5
6
KC-MB30
KC-MB20
KC-D20
KC-D20
KC-B61
KC-B61
KC-MB30
FG(FRAME GROUND)
①
②
③
④
⑤
⑥
⑦
⑧
① : VCC
② : GND
③ : Audio
④ : Video
⑤&⑥ : Door
(Non-Polarity)
⑦ : Camera
angle knob
(Only KC-MB30)
⑧ : Wire clamp
1
2
3
4
4
2
5
5
6
6
1
2
3
4
5
1
① ② ③ ④
① ② ③ ④
■ system configurations
■Name of each connection port
■Cable requirement - Based on distance from a camera to the monitor
■ Camera connection wiring
Monitor back side
Monitor back side
4 WIRE
4 WIRE
4 WIRE
4 WIRE
2 WIRE
2 WIRE
Door Opener
External Power Input
Door Opener
External Power Input
2 WIRE
2 WIRE
Monitor
Option
PABX
Product connection diagram
To connect cameras, put 1~4 monitor wire ports onto camera ports in order with polarity.
1
4
1
4
KC-B61
KC-D20
① ② ③ ④
①②③④
※
Door Open Connection from Monitor :
The monitor should be the version which has door opener port.
※
※
- Upto 100M : CAT5 cable
- Upto 50M : TIV 0.65㎟cable
- Upto 100M : Over TIV 0.8㎟cable
- Upto 150M : TIV 0.8㎟cable + RG-59 / U
RG-59 / U (Coaxial cable) for Video signal
(Connect core to Video & shield to GND)
※
※
CAT5 wire configuration
In case of more than 50m of CAT5 cable length,
the screen and voice quality can get lower.
But the sympthom is not a kind of fault.
So less than 50m is recommended.
Orange
W / Orange
①
VCC
double up
Green
W / Green
②
GND
double up
Blue
W / Blue
③
Audio
double up
Brown
W / Brown
④
Video
double up
[KC-MB20]
Main body
supporter
or
3X5mm
2×8mm
Screw for fixing
camera
Screw for fixing
camera
KC-MB20
※ According to outside environment, you may view the images somewhat unclear.
However, they do not result from any defect or trouble of the product.
①VCC
②GND
③AUDIO
④VIDEO
Camera 1
DC
PABX JACK
1
4
①VCC
②GND
③AUDIO
④VIDEO
Camera 2
①Line 1
②Line 2
Door opener(DC)
1
1
2
4
power
external power
input
Door
opener
