manualshive.com logo in svg

kobi NET-KOBI-IP-16CH, User Manual

Share
Download
kobi NET-KOBI-IP-16CH User Manual Download Page 141

 

 

141 

10.4

 

Configuring Quota Mode 

Purpose: 

Each camera can be configured with allocated quota for the storage of recorded files. 

Steps: 

1.

 

Enter the Storage Mode interface. 

Menu > HDD > Advanced   

2.

 

Set the 

Mode

 to Quota, as shown in Figure 10. 15. 

Note: 

The NVR must be rebooted to enable the changes to take effect.   

   

Figure 10. 15

 

Storage Mode Settings Interface

 

 

3.

 

Select a camera for which you want to configure quota.   

4.

 

Enter the storage capacity in the text fields of 

Max. Record Capacity (GB)

, as shown in Figure 10. 16. 

   

Figure 10. 16

 

Configure Record Quota

 

 

5.

 

You can copy the quota settings of the current camera to other cameras if required. Click the 

Copy

 button to 

enter the Copy Camera menu, as shown in Figure 10. 17. 

Summary of Contents for NET-KOBI-IP-16CH






















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands