KOBE
I N D U S T R I A L
POWER TOOLS
SAFETY INSTRUCTIONS
KOBE
I N D U S T R I A L
POWER TOOLS
SAFETY INSTRUCTIONS
You have purchased a quality industrial product that is
designed for high performance and long service life.
If correct use, safety and maintenance procedures
are observed this product will last for many years.
Thank you for choosing our
KOBE
Electric Fan. Your new fan has been designed using the latest
technology. With normal maintenance, your Electric Fan will provide years of satisfactory performance.
Please read this Owner's Manual carefully before using this fan and save it for future reference.
Be sure your fan is in the OFF position.
Unplug the fan from the electricity supply.
Loosen the grill ring and remove the front grill.
Unscrew the blade clamp by turning it CLOCKWISE
(REVERSE THREAD).
Pull the fan blade away from the motor housing.
Gently wipe the fan blade and grills with a damp
cloth.
DO NOT immerse the fan in water and never allow
water to enter the motor housing.
DO NOT use gasoline, paint thinner or other
chemicals to clean the fan.
For storage, disassemble and clean the fan carefully
as instructed and store in its original box. You may
leave the fan assembled and covered to protect it
from dust. Store the fan in a cool dry place.
CAUTION: To avoid the risk of injury, always make sure that the front and rear
grill are locked together before operating.
When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
electric shock and injury to persons, including the
following:
Always use this fan only as described in this
manual. Other uses not recommended may
cause fire, electric shock or injury to persons.
A l w a y s s u p e r v i s e a s n e c e s s a r y w h e n a n y
appliance is used by or near children.
Always avoid contact with moving fan parts.
Always turn the fan to the OFF position and
unplug the fan from the outlet when not in use
and before cleaning.
Always place the fan on a dry level surface.
Always check that the filters are clear and not
b l o c k e d . K e e p a l l o p e n i n g s c l e a r o f a n y
blockages.
Do not use this product outdoors.
Do not pull by the cord. To disconnect the fan,
first turn control to the OFF position, grip the
plug and pull it from the wall outlet.
Do not operate the fan in the presence of
explosive and/or flammable fumes.
Do not place the fan or any parts near an open
flame, cooking or other heating appliance.
Do not operate the fan with a damaged cord or plug
or if the product malfunctions, is dropped or
damaged in any manner.
Do not hang or mount fan on a wall or ceiling.
Do not operate if the fan housing is removed or
damaged.
Do not operate the fan without checking that the
protective front and rear grill are position.
To protect against electric shock, do not
immerse unit, plug or cord in water or spray with
liquids.
Do not connect this fan to any power source
other than properly grounded ones. DO NOT
attempt to defeat this safety feature. This fan
requires a grounded power source.
The use of attachments is not recommended
and may be hazardous.
A loose fit between the AC outlet (receptacle)
and plug may cause overheating and a distortion
of the plug. Contact a qualified electrician to
replace loose or worn outlet.
If the power cord is damaged, it must be
r e p l a c e d b y t h e q u a l i f i e d e l e c t r i c i a n o r
professional technician in order to avoid a
hazard.
Be sure your fan is in the off position.
Place the fan on a dry and level surface and plug
the cord into a grounded AC 240V 50HZ wall
outlet, which should meet conditions in the
safety instruction.
Tilt the fan grill slightly to desired angle.
Loosening and tightening adjustment: loosen the
tightening screw on the neck of manual control
panel, tilt the fan grill slightly to desired angle,
and then tighten the screw firmly.
Air flow setting: 0=Off, 1=low, 2=Medium,
3=High.
O s c i l l a t i o n : t o a c t i v a t e o r d i s e n g a g e t h e
oscillating feature, push down or pull up on the
oscillation button on the fan head.
1
Front Grill
2
Grill Ring
3
Blade clamp
4
Fan Blade
5
Mounting Nut
6
Rear Grill
7
Motor Housing
8
Oscillation button
9
Speed Switch
10
Base Cover
11
Base
12
Power Cord
Item
Components
GENERAL SAFETY
ASSEMBLY
CLEANING AND STORAGE
OPERATION
SPECIFICATIONS
PLEASE ASSEMBLE FAN ACCORDING TO
ILLUSTRATION DIAGRAM
Step 1.
Remove the rear grill mounting nut. Place the rear grill
onto the motor housing by making sure the two holes
of rear grill fit over the two bumps on the motor
housing. Tighten the rear grill mounting nut
CLOCKWISE.
Step 2.
Assembly of the grill:
Push the fan blade onto the motor shaft and make
sure the screw on the blade is lined up the concave on
motor shaft. Tighten the screw. Be sure the blade can
not be pulled out from the shaft.
Step 3.
Raise the build-in clips around the front grill. Properly
align the front grill over the rear grill and fasten the
clips onto rear grill.
Step 4.
Hold the front grill of the fan, and using a phillips-head
screwdriver loosen the screw slightly on the bottom of
the grill ring, just enough to relieve the tension. Angle
the front grill and the grill ring over the rear grill and
snap into place. Tighten the screw on the
grill ring.
Order Code
KBE-828-0030K
Model No.
KDF300
Power 45W
(Max)
Weight
2.8Kg
Blade Diameter
300mm (12”)
Speed
3
Voltage
AC 240V 50Hz
Oscillating Control
90
°
Head Tilt
Adjustable
Fitted with plug in accordance with BS3456
1
2
3
4
5
6
7
8
9
10
11
12