KOBE DPB350 Operator'S Manual Download Page 1

OPER ATOR’S MANUAL

BENCH MOUNTED PILLAR DRILL

DECLARATION OF CONFORMITY

We hereby certify that the Kobe Model DPB350 Bench Mounted Pillar Drill

complies with all the relevant provisions of the following directives:

LOW VOLTAGE DIRECTIVE 2006/95/EC

MACHINERY DIRECTIVE EN 792, 2006/42/EC

RoHS DIRECTIVE 2002/95/EC

ELECTROMAGNETIC COMPATIBILITY DIRECTIVE 2004/108/EC

STANDARDS APPLIED - EN 80825 - LASERS

Official Agent 

KENNEDY TOOLS

Wigston Works, Leicester, England.

ISO 9001 REGISTERED COMPANY

Signed: 

Date:

1st Jan. 2009     

Name:

Martin Cooke     

Position: 

Director, The Kennedy Group Ltd.

Kobe and the Rising Sun logo are trade marks of Kobe Power Tools.

© The Kennedy Group Ltd.  01/09 

QUALITY GUARANTEE & WARRANTY

KOBE POWER TOOLS carry one years manufacturers warranty.

KOBE POWER TOOLS are designed & produced 

to the highest standards & specifications

KOBE POWER TOOLS are fully guaranteed against 

faulty materials & workmanship

Should they be found to be defective, they will either be repaired or replaced 

free of charge (fair wear and tear and/or misuse excepted). 

This does not affect your legal rights.

Please retain supplier invoice as proof of purchase.

AVAILABLE FROM YOUR DISTRIBUTOR

Please retain this infor mation for future reference.

WARNING:

THE SAFETY INFORMATION

GIVEN INSIDE MUST BE READ AND

UNDERSTOOD BY ANY PERSON 

USING, INSTALLING, REPAIRING 

OR MAINTAINING THIS MACHINE.

Suitable for workshop and light industrial use.

Smooth running 350W motor provides enough
power to drill holes up to 13mm.

5 speeds for versatility and performance
when drilling different materials.

Laser beam target guide for quick positioning
of repeat work.

Tilting rise and fall work table.

Operates from a standard 13amp plug.

Kobe Tools continually strives to improve its products, specifications may change without prior notice.

MODEL DPB350

ORDER CODE

KBE-271-2030K

ALWAYS WEAR

APPROPRIATE

PERSONAL 

PROTECTIVE
EQUIPMENT.

KOBE TOOLS Official Agents:

JAPAN: MIKI TOOL TRADING CO. MIKI CITY, JAPAN.  

EUROPE, MIDDLE EAST, AMERICA & AFRICA: KENNEDY TOOLS, WIGSTON, ENGLAND.

KBE-271-2030K_Instructions.qxd  09/06/2009  09:20  Page 1

Summary of Contents for DPB350









Reviews: