KR-212FHG Instruction Manual Adjustment
EX-1 K.I.Y. setting example.
EX-10 eurus setting example.
Instllation to RC car
First, go to the "System Menu", select
"Response" and change the "OUTPUT" to
"4CH".
From the initial screen, press
the Enter button to access the
"Main Menu". Select the "3/4ch"
menu and then the
"3chControl" menu. From here
scroll to "MODE" and press
Enter. Press the Enter key again
and select "ANALOG" and press
the Enter key.
From the initial screen, press the
Enter button to access the "Main
Menu". Select the "3/4ch" menu
and then the "4chControl" menu.
From here scroll to "MODE" and
press Enter. Press the Enter key
again and select "ANALOG" and
press the Enter key.
Once the "ANALOG" menu is
displayed, you will see that
"KEY" to is set to "OFF". With
"OFF" highlighted, press the
Enter key and change this to
"ET5". Press the Enter key
again to save this setting.
Once the "ANALOG" menu is
displayed, you will see that "KEY"
to is set to "OFF". With "OFF"
highlighted, press the Enter key
and change this to "ET4". Press the
Enter key again to save this
setting.
In this example, ET4 is used but
you can chose any ET that is
available or that you would like to
use.
In this example, ET4 is used but
you can chose any ET that is
available or that you would like to
use.
Now scroll over to "LOW"
where the value is set to
"-100". Press the Enter key to
highlight the value and please
change this value to 0.
Negative values are not used.
The ET4 lever can be used to change the gyro effect for the throttle
Please check the gyro effect. Turn on the power to the receiver
(generally the speed controller power) and move the vehicle to the
right and verify the wheels move to make a left turn. The wheels
should move in the opposite direction of movement of the vehicle.
Please check the gyro effect by first operating the ET5 and check
the "Monitor" display. Adjust the the 3ch position to half of the left
side.
Setting the Steering
Setting the Throttle
Note
Settings for the throttle can be used with reverse as the original
setting.
In the case when the speed controller has an automatic setting for
the throttle, there may be times when it may not operate correctly.
Even in case, it is possible to use with the mixing only of the steering
wheel when the gyro gain of throttle side is set to 0.
If you exit this function and go
to the "Monitor" menu, you
can verify the function by the
cursor movement when
pressing on the ET5 lever.
If the tire movement is in the
same direction of the car
movement, you will need to
set "REVERSE:" to "REVS" in
the "3chControl:ANALOG"
menu.
If the desired movement is opposite, please change the value in the "REVERSE"
setting
IMixing control of the steering and throttle operations of the transmitter
set by the internalized gyro sensor in the receiver. The gyro sensor
effect is called the gyro gain, which is adjusted by the transmitter's 3rd
and 4th channels.
1
1
1
2
3
2
2
3
3
4
4
5
5
Now scroll over to "LOW" where
the value is set to "-100". Press the
Enter key to highlight the value
and please change this value to 0.
Negative values are not used.
The "CEN" and "STEP" values can
also be changed for initial
movement
Please check the response mode setting of your transmitter and verify that it is set to
"NORM" so that you can use 4ch output.
From the "OP" menu, select "CH3" settings. For the "TYPE"
select "3WAY". Set the values of this function to the image
seen to the right.
Next, in the "OP" menu go to "INPUT", and select "Setup".
Scroll down to "E5" and change this to "3:POS" to assign
the 3 way position function to this ET 5 lever.
You can now operate the ET5 lever to activate the 3 steps of the gyro gain. Fine tuning
adjustment can be made by changing the value of each position in the function.
IFor the CH4 settings, set the values the same as CH3 except do not change the value in the reverse setting.
Assign an ET lever to 4:POS for throttle adjustment in the "Setup".
The effectiveness can be adjusted by changing the "STEP" value in the
"3chControl:ANALOG" menu. Also, you can set the "CEN" value to have
the gyro respond immediately after turning.
(Configuration of the numerical value is 0~100).
CH4
>
>
RSP
DD:NORM
INPUT
>
OptionMenu
>
CH3
>
CH4
>
RSP
DD:NORM
OptionMenu
>
TYPE
3
WAY
SUBTRIM 0
REVERSE OFF
POS1 0%
POS2 + 50%
POS3 +100%
C3: -……I……+
>
TYPE
3
WAY
SUBTRIM 0
REVERSE
ON
C3: -……I……+
>
E1 S:TRIM
E2 T:TRIM
E3 T:BRAKE
E4 S:TRAVEL
E5 3:POS
B1 OFF
B2 OFF
OPT:Setup
>
Setup
>
AdjustVR
>
AutoRep 1
OPT:INPUT
Please check the gyro effect. Turn on the power to the receiver and move the vehicle to the right and verify the wheels
move to make a left turn. The wheels should move in the opposite direction of movement of the vehicle.
The chassis
A gyro sensor is installed inside the receiver. Mount the receiver level
on the chassis as shown in the image to the right. There is no
restriction in the direction of mounting the receiver on the chassis.
The gyro detects angle of rotation acceleration, so it can detect nearly
the center or apex of a turn.
Mount the receiver as close to the center of gravity for your vehicle as
possible.
Do not mount the receiver on its side.