manualshive.com logo in svg

Knick SensoGate WA 131 H, User Manual

Share
Download
Knick SensoGate WA 131 H User Manual Download Page 25

25

Removing and Installing the Calibration Chamber

To separate the calibration chamber, you require ZU 0754 or ZU 0740 Service Set (see description 

on page 36). We recommend the ZU 0746 and ZU 0747 mounting aids for proper mounting of 

the  gaskets and scraper rings (see description on page 37).

1) Remove the screws  

(screwdriver TX25).

2) Position a plier and loosen the 

thread of the split calibration 

chamber using a face-pin spanner 

wrench.

3) Completely screw off the split cali-

bration chamber. Now, the gaskets 

are accessible and can be checked 

and replaced if required. Use the 

ZU 0746 and ZU 0747 mounting 

aids for mounting the gaskets and 

scraper rings. 

How to handle the mounting 

aids is described in the respective 

instruction manual.

4) To re-install the split calibration 

chamber, screw the parts together 

using plier and face pin spanner 

wrench and secure them with 

screws.

Note:

The calibration chamber parts 

must be firmly screwed together 

(until the stop is reached) before 

it can be secured with the two 

screws.

Face-pin spanner wrench no. 5  

included in accessory:

ZU 0740, ZU 0754

Mounting pliers  

included in accessory:

ZU 0740, ZU 0754

Summary of Contents for SensoGate WA 131 H

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands