manualshive.com logo in svg

Knick SensoGate WA 131 H, User Manual

Share
Download
Knick SensoGate WA 131 H User Manual Download Page 36

36

Accessories

SensoGate® WA 131 H

ZU 0680

SensoGate® Service Set, Basic

These tools are suitable for minor maintenance opera-

tions. They help separating the drive unit from the 

process unit, allow mounting an Ingold socket and 

replacing the immersion tube including sensor gasket 

maintenance.

ZU 0754

SensoGate® Calibration Chamber Service Set

These tools are suitable for maintenance operations 

at the calibration chamber and its gaskets. They allow 

easy separation of the split calibration chamber.

ZU 0740

SensoGate® Service Set  

Maintenance/Repair/Retrofit

This set provides all tools required for comprehensive 

maintenance, repair or retrofitting of the sensor lock-

gate. With this set, you can completely dismantle every 

SensoGate®.

ZU 0647

Sensor Mounting Wrench

Required for safely screwing in the sensor without over-

loading the PG 13.5 plastic thread of the sensor head by 

an excessive torque (caused by an open-end wrench).

ZU 0747

Mounting Aid for 20 x 2.5 O-Rings

The ZU 0747 mounting aid is used for easy and correct 

fitting of the 20x2.5 O-rings in the calibration chamber 

of the SensoGate®.

Summary of Contents for SensoGate WA 131 H

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands