manualshive.com logo in svg

Knick Portavo 908 MULTI, User Manual

Share
Download
Knick Portavo 908 MULTI User Manual Download Page 29

29

pH

Manual Calibration

(Calibration with manual specification of the number of calibration points and 
the buffer solution) 
1)  Select the number of calibration points and press the Start softkey. 
2)  Adjust the temperature-corrected value (see buffer table) for the 1st/2nd/3rd 

buffer solution and press Continue (repeat this step for each calibration point). 
Note: When using sensors without temperature detector, you should adjust the 
temperature manually before starting calibration (see page 36).

3)  Finally, the calibration data will be displayed.  

You can Apply or Discard these values.

Data Entry Calibration

(Calibration by entering known sensor values)
1)  Press the Start softkey.
2)  Enter the known sensor values for zero and slope. 
3)  Finally, you can Apply these values or Cancel the calibration.

Calibration

Note: To abort calibration, you can press meas at any time.

Calibrating a pH/ORP Combo Sensor

The pH/ORP combo sensor can be calibrated as a pH sensor  
and/or as an ORP sensor.

pH Calibration 
Follow the instructions given for pH calibration, page 28.

ORP Calibration 
Follow the instructions given for ORP calibration, page 30.

pH

ORP

Summary of Contents for Portavo 908 MULTI













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands