Knick Portavo 904 User Manual Download Page 41

Page: 41 / 54

Product Line

Accessories/Options

Item

Order No.

Robust field case (for meter, sensor,
various small parts and user manual)

ZU0934

Li-ion battery (for Portavo 904 COND only)

ZU0925

Replacement quiver (5 units)

ZU0929

Adapter for process sensors with Ø 12 mm and PG 13.5 thread
for use with quiver

ZU0939

Replacement KPG® tube for ZU6985 4-electrode sensor,
incl. O-ring

ZU0180

Replacement flow cell for SE 202 2-electrode sensor

ZU0284

Adapter for connecting a conductivity sensor with
2 banana plugs

ZU0289

Adapter for connecting the ZU6985 4-electrode sensor

ZU0290

Base stand for mounting up to 3 sensors, with base plate made
of stainless steel

ZU6953

Measuring cable with M8 connector for sensors with Memosens connector

Length 1.5 m / 4.92 ft

CA/MS-001XFA-L

Length 2.9 m / 9.51 ft

CA/MS-003XFA-L

Measuring cable for digital toroidal conductivity sensors with
Memosens protocol, 4-pin M12 coupling; 4-pin M8 connector

CA/M12-001M8-L

Measuring cable for connecting 2-/4-electrode sensors with
VP connector

ZU1120

Temperature Detectors

Order No.

Pt1000 temperature detector

ZU6959

Pt1000 temperature detector with angled connector

ZU0156

Note:

When a Memosens sensor is connected, the temperature detector of the

Memosens sensor is used. When a Memosens sensor is not connected, the Portavo
can be used as a temperature meter.

Summary of Contents for Portavo 904























































Search results

Summary of Contents for Portavo 904

Reviews:

Related manuals for Portavo 904

Brands by name

Popular brands

Knick Portavo 904, User Manual

Search results

Summary of Contents for Portavo 904

Reviews:

Related manuals for Portavo 904

Brands by name

Popular brands