Knick Portavo 904 User Manual Download Page 21 | Manualshive

Page: 21 / 54

background image

21

Measurement

cal

CAL
TEMP. OFFSET

You can specify an offset for the temperature

measured by the sensor.

After calibration has been activated, the follow-

ing values are listed in the display:
•  temperature setpoint
•  temperature measured by sensor
•  offset (display in K)

cal

Temperature setpoint value
blinks.

Use



to set the temperature setpoint value.

cal

Calibration is performed.
Display: TEMP. OFFSET.
The meter then automatically returns to measuring mode.

TEMP. OFFSET Calibration (option)

Temperature calibration (offset)

Selected in the configuration menu.

Note:

To abort calibration, you can press

meas

at any time.

Calibration

Calibration

«
...
19
20
21
22
23
...
»

Summary of Contents for Portavo 904























































Reviews:

No comments

Related manuals for Portavo 904

Brand: HANYOUNG NUX Pages: 4

Brand: jenway Pages: 30

Brand: National Meter & Automation Pages: 24

Brand: Lakeshore Pages: 2

Brand: Kamstrup Pages: 4

Brand: Kawai Pages: 22

Concert Performer CP3

Brand: Kawai Pages: 40

Brand: Kawai Pages: 36

Brand: Kawai Pages: 148

Brand: Kawai Pages: 30

Classic Series CS6

Brand: Kawai Pages: 96

Brand: Katronic Pages: 3

FLUXUS ADM 6725

Brand: Katronic Technologies Pages: 148

Brand: Kawai Pages: 176

Brand: Axio MET Pages: 5

PRO VPR100 Series

Brand: CTC Union Pages: 10

Brand: PCB Piezotronics Pages: 15

Brand: Sercel Pages: 63

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands