KNF FK 1100 Installation Instructions Manual Download Page 5 | Manualshive

Page: 5 / 22

KNF FK 1100 Installation Instructions Manual Download Page 5

Installation Instructions FK 1100

General

KNF Flodos 178057_MA_FK1100_EN_00.docx

5

1.3 Disclaimer

The manufacturer accepts no liability for damage or malfunctions
that are caused by non-compliance with the Installation Instruc-
tions.

The manufacturer accepts no liability for damage or malfunctions
that are caused by modifications to or conversions of the device or
by improper handling.

The manufacturer accepts no liability for damage or malfunctions
that are caused by using spare parts or accessories that are not
approved by the manufacturer.

1.4

Manufacturer’s address

KNF Flodos AG
Wassermatte 2
6210 Sursee, Switzerland

Phone +41 (0)41 925 00 25
Fax +41 (0)41 925 00 35

1.5 Supporting documents

The listed documents must also be observed. The valid versions
are available at

www.knf.com/downloads

▪

Data sheet

▪

3D model

The following must also be observed:

▪

Local T&Cs

▪

Sales documents and agreement between KNF and the cus-

tomer

▪

Drive specification

«
...
3
4
5
6
7
...
»

Summary of Contents for FK 1100























Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands