KMC Controls MEP-7 Series Application Manual Download | Manualshive

Page: 6 / 11

background image

MEP-7xxx Direct-Coupled Actuators (up to 320 in-lb.)

6

Applications Guide, AN1113A Rev. D

The

crank arm kit is used when direct

mounting of the actuator is impractical.

non-rotation bracket is provided

with each actuator. It can span an open distance, or

be formed (bent) into a shape that increases the dis-

tance between the mounting surface and the actua-

tor.

Mounting Brackets and Crank Arm Kit

«
...
4
5
6
7
8
...
»

Summary of Contents for MEP-7 Series












Reviews:

No comments

Related manuals for MEP-7 Series

Brand: E-fly Pages: 16

Brand: Icom Pages: 30

Brand: ICM Controls Pages: 2

Brand: ICM Controls Pages: 2

Brand: ray Pages: 11

Brand: Lamtec Pages: 22

MachXO5-NX Development Kit

Brand: Lattice Semiconductor Pages: 2

Brand: Rain Bird Pages: 138

Brand: S&P Pages: 12

Brand: S&C Pages: 34

Brand: S&C Pages: 32

IntelliCap Plus

Brand: S&C Pages: 32

Brand: S&P Pages: 12

Brand: S&C Pages: 35

Brand: Talgil Pages: 14

Brand: Tadao Pages: 2

Brand: J+J Pages: 4

Brand: Val Controls Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands