background image

 

Instruction Manual

 IDO

8065

-HILO

8065

 

 

 
09/01/19     Rev: 1.0. 0                                                                                               (TRANSLATION OF ORIGINAL LANGUAGE) 

21 

8. 

REASONABLY FORESEEABLE INCORRECT USE OF THE MACHINE 

 

 

 

The machine is not intended for outdoors use. 
Do not wash and extract corrosive, flammable, explosive liquids, even if diluted. 
It is strictly forbidden to use the machine in environments with explosion hazard where there are 
flammable and explosive gases, vapours, liquids and powders. 
 

 

Do not wash the floors with water hotter than 50°C; 
Do not use diesel fuel/benzene or corrosive detergents for washing floors; 
 
 

 

The machine has been designed to work on flat surfaces and minor gradients.  
The maximum permitted gradient, which can be travelled up either during operation or transfers, is 

2%

To travel down, it is recommended to move in reverse for optimal performance.  
If one travels down in the travel direction, owing to the possible surface condition (wet, uneven or low 
friction material) dangerous slipping may occur, or long braking space, even more evident and hazardous 
when transferring and moving the machine, when the brush plate is lifted from the floor. 

9. 

SUPPLIED KIT 

 
No other material is supplied with the machine in addition to this instruction manual. 

10. 

INSTALLATION 

10.1.  Preliminary operations 

 
The machine is shipped completely assembled and packed on a pallet.  
To load the machine from the pallet, resting it on the floor, use the special slide platform. It is 
recommended not to push the machine down the pallet without a suitable ramp.  
 

Summary of Contents for TRION Series











































Reviews: