Klein + Hummel M 52 Operating Manual Download Page 15

 

Klein + Hummel 

M 52 (D) 

Page 13 

 

 

    

M 52 (D) dist

M 52 (D) dist

M 52 (D) dist

M 52 (D) distortion at 90 dB SPL

ortion at 90 dB SPL

ortion at 90 dB SPL

ortion at 90 dB SPL    

 
 

Safety and Warnings

Safety and Warnings

Safety and Warnings

Safety and Warnings 

 

In addition to specific warnings throughout this document, please observe these additional general instructions.  

 
This symbol means that a high voltage is to found nearby. Take appropriate precautions to avoid electric 
shocks. 
 

 

This symbol means that hot parts of the product may be found nearby. Take appropriate precautions to 
avoid burns. 
 

 

General

General

General

General    

 

Keep these instructions in a safe place for future reference. 

 

Failure to follow the safety and warning instructions contained in this document voids the warranty. 

 

This product should be used for the intention for which it was designed and as described in this document. 

 

Environment

Environment

Environment

Environment    

 

Ensure that the room in which you use this product is wired in accordance with the local electrical code and 
checked by a qualified inspector. 

 

A correctly earthed mains power connection should always be used. 

 

If access to the interior electronics is required, disconnect it from the mains power and allow electrical energy 
storage devices, such as capacitors and transformers, to discharge. 

 

Other electronic products may generate sufficient heat to require ventilation. 

 

Do not block or cover heatsinks, fans, or vents. 

 

Unless otherwise stated, this product is designed to be used indoors only. 

 

Do not expose this product to water, any other liquids, moisture, or naked flames. 

 

Do not install this product into hot, humid, or excessively dusty locations, or into direct sunlight. 

 

Avoid installing this product into locations where it will experience externally generated vibrations or heat (e.g. 
radiators). 

 

If the product is moved from a cold environment into a warm one (such as from a vehicle into a building), it is 
possible that condensation will form. Please allow the product sufficient time for acclimatization to room 
temperature before using. 

 

Wherever an amplifier is located, a free flow of air should be maintained by leaving a gap of at least 5 cm (2”) 
around it. A flush mounted cabinet with the electronics panel still installed should be well-ventilated to avoid heat 
build-up and possible risk of fire. 

 

Use

Use

Use

Use    

 

The equipment should be mounted by a suitably qualified professional in accordance with local, national, and 
international regulations and standards. 

 

Falling equipment can damage itself, people, and other objects, so do not place this unit on any unstable platform, 
cart, trolley, stand, table, or mounting hardware. 

 

Do not use accessories and options with this product that are not approved by Klein + Hummel. 

 

Mounting hardware must be attached to the appropriate hardware and attachment points rated and intended for 
such use. 

 

Ensure that the operating voltage of this product matches that of the local mains voltage. 

 

Use the power cable that came with this product as this has been manufactured to international safety standards. 
If it has been damaged obtain a similarly certified and specified mains power cable. 

 

This product should be unplugged from the mains power and the signal sources if is not to be used for an 
extended period of time, or during lightening storms. 

Summary of Contents for M 52





















Reviews: