Kleenmaid SPOT120, Instructions For Use And Warranty Details, Page: 7 / 12

4
Consult the designs in the front pages referenced in the text by
alphabet letters. Closely follow the instructions set out in this
manual.All responsibility, for any eventual inconveniences, damages
or fires caused by not complying with the instructions in this manual,
is declined.
The rangehood must be placed at a minimum distance of 650mm
from the cooking plane for electric, gas and mixed cooktops.
Please confirm measurement with your Local Building Authority.
The rangehood is equipped with a top air outlet "B“ for discharge of
fumes to the outside (Ducting version – exhaust pipe and pipe
fixing clamps not provided).
Should it not be possible to discharge cooking fumes and vapour to
the outside, the rangehood can be used in the filter version, by
fitting an activated carbon filter and the deflector "F“ on the support
(bracket) "G“. Fumes and vapours are recycled through the top
grille "H“ by means of an exhaust pipe connected to the top air outlet
"B“ and the connection ring mounted on the deflector "F“(exhaust
pipe and pipe fixing clamps not provided).
Expansion wall plugs are provided to secure the rangehood to most
types of walls/ceilings. However, a qualified technician must verify
suitability of the materials in accordance with the type of wall/ceiling,
which must be strong enough to take the weight of the rangehood.
Installation - Fig. 5
Preliminary information for installation of the rangehood:
Disconnect the rangehood during electrical connection, by
turning the home mains switch off.
Remove the grease filter/s.
Do not tile, grout or silicone this appliance to the wall. Surface
mounting only.
Do not fix chimney flue to furniture or fly over shelves unless the
chimney flue can be easily removed, in case maintenance is ever
required.
Assembling the chimney flue support/bracket (3 parts):
The three parts should be fixed with 4 screws, the support extension
is adjustable and should correspond to the internal width of the
telescopic chimney flue.
Assembling the deflector (only when a deflector composed of 3
parts is supplied – the deflector should be only for the filter
version):
The three parts should be fixed with 2 screws, the deflector extension
is adjustable and should correspond to the width of the chimney flue
support, to which it is then fixed.
=
=
X
X
H
=
=
X
F
F
G
G
1. Using a pencil, draw a line on the wall, extending up to the
ceiling, to mark the centre. This will facilitate installation.
2. Rest the drilling template against the wall: the vertical centre line
printed on the drilling template must correspond to the centre
line drawn on the wall, and the bottom edge of the drilling
template must correspond to the bottom edge of the rangehood.
Bear in mind that, when installation is complete, the underside
of the rangehood must be at least 650mm above electric, gas
or mixed cooktops. Please confirm this measurement with
your Local Building Authority.
4. Rest the support bracket on the drilling template so that it
coincides with the dotted rectangle. Mark the two outer holes
and drill them. Remove the drilling template, insert 2 wall plugs
and fix the rangehood support bracket into place using two
5x45mm screws.
5. Hang the rangehood on the bracket.
6. Adjust the distance of the rangehood from the wall.
7. Adjust the horizontal position of the rangehood.
8. Using a pencil mark the rangehood permanent drill hole inside
the suction group (2 fixing points are necessary for permanent
mounting).
9. Remove the rangehood from the bracket.
10. Drill at the point marked (Ø8mm - see operation 8).
11. Insert 1 or 2 wall screw anchors according to requirement.
12. Rest the chimney support bracket "G“ against the wall, touching
the ceiling. Use the support bracket as a drilling template (the
small slot formed on the support must coincide with the line
drawn on the wall as above – operation 4) and mark 2 holes with
a pencil, drill the holes (Ø8mm), insert 2 wall plugs.
13. Fix the chimney support bracket to the wall using two 5x45mm
screws.
14. Hook the rangehood onto the bottom bracket.
15. Fix the rangehood into its final position on the wall
(ABSOLUTELY ESSENTIAL).
16. Connect a pipe (pipe and pipe clamps not provided, to be
purchased separately) for discharge of fumes to the connection
ring located over the suction motor unit.
If the rangehood is to be used in ducting version, the other end
of the pipe must be connected to a device expelling the fumes
to the outside. If the rangehood is to be used in filter version,
then fix the deflector "F" to the chimney support bracket "G"
and connect the other extremity of the pipe to the connection
ring placed on the deflector "F".
17. Make the electrical connections.
18. Apply the chimney stacks and fasten them at the top to the
chimney support "G“ (20b) using 2 screws (20a).
19. Slide the bottom section of the chimney down until it completely
covers the suction unit and slots into the housing provided on top
of the rangehood.
Replace the grease filter/s and check that the rangehood is
operating correctly.
Electrical connection
The electrical tension must correspond to the tension noted on the
label placed inside the rangehood. Connect the electrical plug,
where provided, to the an easily accessible outlet in conformity with
local standards in force.
Where an electrical plug is not provided (for direct connection to
electrical network) place a standards approved bipolar switch with
an aperture distance of not less than 3mm (accessible) from the
contacts.