background image

 

 

User instructions 

 

 

 

 

 

2.  Installation and hook-up 

 

 

 

 

Remove the polystyrene basket retainers.  
Position  the  appliance  in  the  desired  place  of  installation.  The  back  or 
sides  of  the  dishwasher  may  be  placed  up  against  walls  or  other 
furniture  units.  If  the  dishwasher  is  installed  near  a  heat  source,  fit  the 
special  insulating  panel  to  prevent  overheating  and  malfunction  of  the 
appliance.  To  ensure  stability,  install  integrated  or  built-under 
dishwashers  only  under  continuous  worktops,  and  screw  them  to  the 
adjacent  units.  To  facilitate  the  installation  procedure,  the  intake  and 
drain hoses can be positioned in any direction; make sure that the hoses 
are  not  kinked,  crushed  or  pulled  too  tightly.  Make  sure  to  tighten  the 
locking  ring-nut  once  the  pipes  have  been  placed  in  the  direction 
required.  A  hole  at  least  8  cm  in  diameter  is  required  to  allow  the  power 
supply cable and pipes to pass. 

 

 

Level the appliance on the floor using its adjustable feet. This operation 
is essential for ensuring correct operation of  the dishwasher. 

 

 

 

 

Building-in  a  dishwasher  underneath  a  ceramic  cooktop  is  absolutely 
forbidden

 
Moreover,  dishwashers  may  not  be  installed  directly  touching 
appliances  which  are  not  conventional  built-in  kitchen  appliances  (e.g. 
fireplaces, stoves, etc.).  
 
When  installing  the  dishwasher  in  a  compartment  next  to  one  or  more 
other  appliances,  it  is  essential  to  comply  with  all  the  recommendations 
provided by the appliance’s manufacturer (minimum distances, installation 
procedures, etc.). 

 

 

 

 

This  model  is  equipped  with  only  one  adjustable  foot  at  the  rear,  which 
can  be  adjusted  by  turning  the  screw  on  the  lower  front  part  of  the 
appliance. (Use 8mm socket on electric screwdriver) 

 

 

2.1 

Water supply connection 

 
 

 

 

 

Preventing the risk of clogging or damage: if the water pipe is new or 
has not been used for a long time, before connecting to the water supply 
check that the water is clear and free of impurities, to prevent damage to 
the appliance.  
The  dishwasher  must  always  be  connected  to  the  water  system 
with new hoses; old or used hoses must never be reused.
 

 

 

Summary of Contents for DW6011





































Reviews: