background image

7

To turn on Holiday Mode, press and hold the COOLING 
button for 3 seconds to enter adjust mode. Then press and 
hold ICE and LIGHT at the same time for 3 seconds. When 
the feature turns on, “Holiday Mode” will appear on the 
dispenser display. 

To turn Holiday Mode off, press and hold OPTIONS for 
3 seconds.

Temperature Display Always On 

This feature keeps the temperature display on at all times. 

Press and hold COOLING and LOCK at the same time for 
3 seconds to turn the feature on. 

IMPORTANT: To avoid unintentionally locking the dispenser 
or changing other settings, be sure to press both buttons at 
exactly the same time.

Press and hold COOLING and LOCK at the same time for 
3 seconds again to turn the feature off.

Door Ajar Alarm

The Door Ajar Alarm feature sounds an alarm when the 
refrigerator or freezer door is open for 5 minutes and the product 
cooling is turned on. The alarm will repeat every 2 minutes. Close 
both doors to turn it off. The feature then resets and will 
reactivate when either door is left open again for 5 minutes.

Disabling Sounds

To turn off all dispenser and control sounds, including the 
Door Ajar Alarm, press and hold ICE and OPTIONS at the 
same time for 3 seconds.

To turn all sounds back on, press and hold ICE and OPTIONS 
at the same time for 3 seconds again.

Convertible Drawer Temperature Control

(on some models)

The control can be adjusted to properly chill meats or vegetables. 
The air inside the pan is cooled to avoid “spot” freezing and can 
be set to keep meats at the National Livestock and Meat Board 
recommended storage temperatures of 28° to 32°F (-2° to 0°C). 
The convertible vegetable/meat drawer control comes preset at 
the lowest meat setting.

To store meat:

Set the control to one of the three MEAT settings to store meat at 
its optimal storage temperature.

To store vegetables: 

Set the control to VEG to store vegetables at their optimal 
storage temperatures. 

NOTE: If food starts to freeze, move the control to the left (less 
cold). Remember to wait 24 hours between adjustments.

  Crisper Humidity Control 

(on some models)

You can control the amount of humidity in the moisture-sealed 
crisper. Adjust the control to any setting between LOW and 
HIGH.

LOW (open) for best storage of fruits and vegetables with skins. 

HIGH (closed) for best storage of fresh, leafy vegetables. 

Chilled Door Bin

(on some models)

Cool air from the freezer is directed to the refrigerator door bin 
directly beneath the vents.

NOTE: The dairy compartment and can rack are not associated 
with the Chilled Door Bin feature.

Chilled Door Bin Control

The chilled door bin control is located on the left-hand side of the 
refrigerator compartment.

Slide the door chill control to the left to reduce the flow of 
cold air to the bin and make it less cold. 

Slide the door chill control to the right to increase the flow of 
cold air to the bin and make it colder.

Water and Ice Dispensers

(on some models)

Depending on your model, you may have one or more of the 
following options: the ability to select either crushed or cubed 
ice, a special light that turns on when you use the dispenser, or a 
lock option to avoid unintentional dispensing.

NOTES:

The dispensing system will not operate when the freezer door 
is open.

After connecting the refrigerator to a water source, flush the 
water system. Use a sturdy container to depress and hold the 
water dispenser lever for 5 seconds, then release it for 
5 seconds. Repeat until water begins to flow. Once water 
begins to flow, continue depressing and releasing the 
dispenser lever (5 seconds on, 5 seconds off) for an 
additional 2 minutes. This will flush air from the filter and 
water dispensing system. Additional flushing may be required 
in some households. As air is cleared from the system, water 
may spurt out of the dispenser. 

Allow 24 hours for the refrigerator to cool down and chill 
water.

Allow 24 hours to produce the first batch of ice. Discard the 
first three batches of ice produced.

The display screen on the dispenser control panel has a 
backlight, which will turn off automatically when the control 
buttons have not been used for 30 seconds or more. When 
the backlight is off, the first press of a control button will only 
reactivate the backlight, without changing any settings. 
Within 30 seconds after the backlight has been reactivated, 
additional presses of control buttons will change the 
applicable settings.

The Water Dispenser

IMPORTANT: Dispense enough water every week to maintain a 
fresh supply.

To Dispense Water:

1. Press a sturdy glass against the water dispenser lever.

2. Remove the glass to stop dispensing.

A. Chilled door bin control

A

Summary of Contents for KSRK25FVBL - 25.4 cu. ft. Refrigerator

































Reviews: