![background image](http://html.mh-extra.com/html/kitchenaid/ksdg950ess/ksdg950ess_manual_198314009.webp)
9
Parts Needed
If using a power supply cord kit:
�
A UL listed power supply cord kit marked for use with ranges.
The cord should be rated at 250 V minimum, 40 A or 50 A that
is marked for use with nominal 1
3
⁄
8
" (3.5 cm) diameter
connection opening and must end in ring terminals or open-
end spade terminals with upturned ends.
�
A UL listed strain relief.
Check local codes and consult gas supplier. Check existing gas
supply and electrical supply. See the appropriate “Electrical
Requirements” and “Gas Supply Requirements” sections.
It is recommended that all electrical connections be made by a
licensed, qualified electrical installer.
NOTE:
Be sure to purchase only Whirlpool factory-certified parts
and accessories for your appliance. Your installation may require
additional parts. To order, refer to the contact information
referenced in your Quick Start Guide.
Optional Parts
To purchase these or any other accessories, refer to the Quick
Start Guide for ordering information.
�
Side Trim Kits:
5/8" (1.7 cm) White - Order Part Number W10675027
5/8" (1.7 cm) Black - Order Part Number W10675026
5/8" (1.7 cm) Stainless Steel - Order Part Number W10675028
1
1
⁄
8
" (2.9 cm) White - Order Part Number W10731885
1
1
⁄
8
" (2.9 cm) Black - Order Part Number W10731886
1
1
⁄
8
" (2.9 cm) Stainless Steel - Order Part Number W10731887
�
Backsplash Kits:
High 6" (15.2 cm) White - Order Part Number W10655448
High 6" (15.2 cm) Black - Order Part Number W10655449
High 6" (15.2 cm) Stainless Steel - Order Part Number
W10655450
NOTE:
Be sure to purchase only Whirlpool factory-certified parts
and accessories for your appliance. Your installation may require
additional parts. To order, refer to the contact information
referenced in your Quick Start Guide.
Location Requirements
IMPORTANT:
Observe all governing codes and ordinances. Do
not obstruct flow of combustion and ventilation air.
�
It is the installer’s responsibility to comply with installation
clearances specified on the model/serial/rating plate. The
model/serial/rating plate is located behind the oven door on the
top right-hand side of the oven frame.
�
The range should be located for convenient use in the kitchen.
�
Recessed installations must provide complete enclosure of the
sides and rear of the range.
�
All openings in the wall or floor where range is to be installed
must be sealed.
�
Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
�
The anti-tip bracket must be installed. To install the anti-tip
bracket shipped with the range, see “Install Anti-Tip Bracket”
section.
�
Grounded electrical supply is required. See the appropriate
“Electrical Requirements” section.
�
Proper gas supply connection must be available. See “Gas
Supply Requirements” section.
�
Contact a qualified floor covering installer to check that the
floor covering can withstand at least 200°F (93°C).
�
Use an insulated pad or 1/4" (6.4 mm) plywood under range if
installing range over carpeting.
IMPORTANT:
To avoid damage to your cabinets, check with your
builder or cabinet supplier to make sure that the materials used
will not discolor, delaminate or sustain other damage. This oven
has been designed in accordance with the requirements of UL
and CSA International and complies with the maximum allowable
wood cabinet temperatures of 194°F (90°C).
Mobile Home - Additional Installation
Requirements
The installation of this range must conform to the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction and
Safety, Title 24, HUD Part 280). When such standard is not
applicable, use the Standard for Manufactured Home Installations,
ANSI A225.1/NFPA 501A or with local codes.
In Canada, the installation of this range must conform with the
current standards CAN/CSA Z240.1 - latest edition, or with local
codes.
Mobile Home Installations Require:
�
When this range is installed in a mobile home, it must be
secured to the floor during transit. Any method of securing the
range is adequate as long as it conforms to the standards
listed above.
�
Four-wire power supply cord or cable must be used in a mobile
home installation. The appliance wiring will need to be revised.
See “Electrical Connection - U.S.A. Only” section.
Cabinet Dimensions
Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm)
countertop height.
IMPORTANT:
If installing a range hood or microwave hood combination above the cooking surface, follow the range hood or microwave
hood combination installation instructions for dimensional clearances above the cooktop surface.
NOTE:
When installed in a slide-in cutout, the front of oven door may protrude beyond the base cabinet.
Summary of Contents for KSDG950ESS
Page 70: ...REMARQUES ...
Page 71: ...REMARQUES ...