background image

22

22

22

22

22

22

NOTE:

 To mute the audible alarm while keeping the doors open, 

such as while cleaning the inside of the refrigerator, press any 
button on the control panel. The alarm sound will be temporarily 
turned off, but the Door Ajar icon will still be displayed on the 
dispenser control panel.

Disabling Sounds

To turn off control and dispenser sounds, press and hold ICE/
WATER and MEASURED FILL at the same time for 3 seconds. 
All normal operating tones are disabled. Only alert tones will 
be audible.

To turn all sounds back on, press and hold ICE/WATER and 
MEASURED FILL at the same time for 3 seconds again.

Power Outage

The Power Outage indicator lets you know if the power supply to 
the refrigerator has been off and the freezer temperature has risen 
to 18°F (-8°C) or higher.
The control panel temperature display will read “PO,” and an 
alert tone will sound three times. “Confirm” will blink until you 
acknowledge the power outage by pressing MEASURED FILL 
under “Confirm.” 
Once the power outage has been confirmed, the “PO” will 
disappear, and the display will return to the Home screen. 

Showroom Mode

This mode is used only when the refrigerator is on display in a 
retail store. If you unintentionally turn on Showroom mode, the 
word “Showroom” will light up on the display. Exit Showroom 
mode by pressing and holding LIGHT and LOCK at the same 
time for 3 seconds. 

Refrigerator Features

Temperature Controlled Exterior Drawer 

IMPORTANT: 

The left-hand refrigerated drawer has its own 

temperature control. This control sets the temperature for this 
drawer only. The temperature for the right-hand drawer is set to 
the same temperature as the main refrigerator compartment.   
Temperatures have been preset for the storage of: Meat/Fish, 
Cold Drinks, Greens/Herbs, Deli/Cheese, and Thaw/Marinate. 
These preset temperatures cannot be adjusted. 

Press SELECT to toggle through the temperature settings. 
The icon will illuminate when it is selected. 

Removable Interior Drawer Bins

The drawer bins are removable for ease in cleaning. 

To remove and replace the interior bins:

1.

To remove, grasp the sides of the bin and lift up and out. 

2.

To replace, with the rear of the bin facing the back of the 
refrigerator, lower the bin onto the drawer glides. See 
“Remove and Replace Drawer Fronts.” 

Adjustable Drawer Bin Dividers

Each refrigerated drawer has an interior drawer bin with a divider 
that can be inserted into one of three different positions or 
removed to customize the space for your food storage needs. 

Easy Slide Bin 

A shallow storage compartment with glass lids, which slide from 
side to side is located below and in front of the crisper drawers. 

NOTE:

 This compartment is not temperature or humidity 

controlled, so it is not recommended for storing leafy vegetables. 

To remove Easy Slide bin:

1.

Remove all three crisper drawers.

2.

Hold the upper sliding lid near the trim and lift up to remove. 
Remove the lower lid.

3.

Grasp the front of the bin with both hands and lift up on the 
front to remove. 

To replace Easy Slide bin:

1.

Slightly tilt the rear of the bin upward.

2.

Align the center rib and tabs on the Easy Slide bin with the ribs 
and slots in the cabinet.

3.

Lower the bin into place. 

Herb Box

A box to store herbs and the water to keep them fresh is located 
within the Easy Slide bin. For your convenience, you can 
reposition the herb box anywhere along the length of the bin.

1.

Slide open one of the bin doors to access the herb box. 

2.

Remove the herb box from the bin using two hands. One hand 
should hold the box while the other hand holds the lid. 

3.

Grasp the handle between your fingers and lift up to remove 
the lid. 

NOTE:

 The bottom of the herb box is angled so that the roots 

of the herbs can be submerged in water while the leaves 
remain dry.

Meat/Fish

32°F (0°C)

Cold Drinks

34°F (1°C)

Greens/Herbs

36°F (2°C)

Deli/Cheese

38°F (3°C)

Thaw/Marinate

39°F (4°C)

A. Crisper drawer handles
B. Easy Slide bin

A

B

Summary of Contents for KRMF706ESS00





































Reviews: