background image

8

8

8

8

8

8

3. Left-hand drawer only, disconnect the wiring. 

NOTE: The drawer front of the left-hand refrigerated drawer is 
connected to the temperature control by wires running 
underneath the drawer glide. Before removing the drawer 
front, the wires must be disconnected. 

On one side of the wiring connector, insert the screwdriver 
blade between the connector tab and the connector to 
release. Repeat for the opposite side. Pull the wiring 
connector apart. 

4. Remove the drawer front.

Push up on the lever at the bottom of the drawer glide 
bracket to release the drawer front from the bracket.    

Lift the drawer front up and off the drawer glide brackets.

5. Slide the drawer glides back into the refrigerator. 

Replace the Drawer Fronts

1. Pull out the drawer glides until they are fully extended.
2. Push up on the lever at the bottom of the drawer glide bracket 

to open. Insert the drawer front bracket into the drawer glide 
bracket and release the lever. 
NOTE: It helps if one person holds the drawer glides steady 
while another person aligns the drawer front and connects the 
brackets. 

3. Left-hand drawer only, reconnect wiring.

Align the two ends of the wiring connector and push them 
together until you hear a “click” sound and feel the tabs 
snap into place on the connector. 

Gently pull on the wiring connection to ensure the wiring 
connection is completely seated. Replace the wiring 
cover.

NOTE: The wiring connection must be complete for the 
drawer temperature control to operate. 

4. Left-hand drawer only, replace the wiring connection cover. 
5. Replace the drawer bins onto the drawer glides with the rear 

side of the bin facing the back of the refrigerator as shown.
IMPORTANT: The Door Ajar alarm will sound if the interior 
drawer bins are not replaced correctly. The bins are designed 
with a specific front and rear. They must be placed into the 
drawers, as shown, so that the refrigerated drawers will close 
and operate properly. 

A. Drawer glide bracket

B. Release lever

A

B

A. Faces back of refrigerator (insert first)
B. Faces front of refrigerator

A

B

Summary of Contents for KRMF606ESS






































Reviews: