3
Electrical Requirements
Observe all governing codes and ordinances.
Required:
■
A 120-volt, 60 Hz, AC-only, 15- or 20-amp electrical supply
with a fuse or circuit breaker.
Recommended:
■
A time-delay fuse or time-delay circuit breaker.
■
A separate circuit serving only this microwave oven.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
GROUNDING INSTRUCTIONS
SAVE THESE INSTRUCTIONS
■
For all cord connected appliances:
The microwave oven must be grounded. In the event of
an electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric
current. The microwave oven is equipped with a cord
having a grounding wire with a grounding plug. The plug
must be plugged into an outlet that is properly installed
and grounded.
WARNING:
Improper use of the grounding plug can
result in a risk of electric shock. Consult a qualified
electrician or serviceman if the grounding instructions are
not completely understood, or if doubt exists as to whether
the microwave oven is properly grounded.
Do not use an extension cord. If the power supply cord is
too short, have a qualified electrician or serviceman install
an outlet near the microwave oven.
This device complies with Part 18 of the FCC Rules.
This device complies with Industry Canada ICES-001.
OPERATING YOUR MICROWAVE OVEN
Settings
Clock
The Clock is a 12-hour (12:00-11:59) or 24-hour (0:00-23:59)
clock. Touch SETUP/CLOCK to reach Clock submenu and follow
the prompts to set the Clock. Clock format (12 hours with AM and
PM, 12 hours without AM and PM or 24 hours) may also be set in
the Clock submenu.
Timer
With the microwave oven in Standby mode, touch the Timer
keypad, enter time, then touch the Timer keypad or the Start
keypad. Cook functions may be entered while the Timer is
counting down. To cancel timer, touch Timer keypad while the
Timer countdown is active in the display.
Control Lock
Activate to avoid unintended start. Touch and hold the Cancel
keypad for about 3 seconds until 2 tones sound and padlock
icon appears in the display. Repeat to unlock control.
Setup/Clock
Ten options/settings may be adjusted: 1-Set Clock; 2-Scrolling
Speed; 3-Sound; 4-Filter Reset; 5-Fan Timer; 6-Light Timer;
7-Language (English or French); 8-Calibrate Temp; 9-Demo Mode;
10-Factory Reset.
Scroll Speed
Scroll speed of the text may be adjusted. Touch SETUP/CLOCK
to reach the Scroll Speed submenu and follow the prompts to
set speed.
Sound (Tones)
Programming tones and signals. Programming tones may be
turned off or all tones (including end-of-function signals) may be
turned off. Touch SETUP/CLOCK to reach the Sound submenu,
then follow the prompts to turn off or on the programming tones
or all tones.
Filter Reset
Reset the filter status after replacing and/or cleaning the filters.
Touch SETUP/CLOCK to reach the Filter Reset submenu and
activate reset.
Vent Fan
Various speeds, ranging from high to low, and off. Comes on
automatically as cooling fan during any cook function.
Fan Timer:
Set vent fan to run for exactly 30 minutes or to run for
only 30 minutes more (off after 30 minutes). The vent fan may be
turned off at any time using the Vent Fan control. Touch SETUP/
CLOCK to reach the Fan Timer submenu and select the setting.
Light Timer
Set the cooktop light to turn on and off at certain times. Touch
SETUP/CLOCK to reach the Light Timer submenu and follow
the prompts to set the light on time and light off time in hours
and minutes or to cancel Light Timer.
NOTE:
Light Timer uses 12-hour clock only.
Language (on some models)
Language of the display text may be changed. Touch the SETUP/
CLOCK to reach the Language submenu, and follow the prompts
to set language to English or French.
Calibration
The actual convection cooking temperature may be calibrated
higher or lower than the displayed temperature. For example,
if you want the microwave oven to be a bit hotter, you may try
setting the calibration to +10°. Touch SETUP/CLOCK to reach the
Calibration submenu. Use number keypads to select temperature
variations in degrees Fahrenheit: 1 = ±0° (reset to default), 2 = +5°
(+2.8°C), 3 = +10° (+5.6°C), 4 = +15° (+8.3°C), 5 = +20° (+11.1°C),
6 = -5° (-2.8°C), 7 = -10° (-5.6°C), 8 = -15° (-8.3°C), and 9 = -20°
(-11.1°C).