background image

23

General Cleaning

IMPORTANT: Before cleaning, make sure all controls are off and 
the oven and cooktop are cool. Always follow label instructions on 
cleaning products.

Soap, water and a soft cloth or sponge are suggested first unless 
otherwise noted.

EXTERIOR PORCELAIN ENAMEL SURFACES

(on some models)

Food spills containing acids, such as vinegar and tomato, should 
be cleaned as soon as the entire appliance is cool. These spills 
may affect the finish.

Glass cleaner, mild liquid cleaner or nonabrasive scrubbing 
pad:

Gently clean around the model and serial number plate 
because scrubbing may remove numbers.

STAINLESS STEEL (

on some models)

Do not use soap-filled scouring pads, abrasive cleaners, Cooktop 
Polishing Creme, steel-wool pads, gritty washcloths or some 
paper towels. Damage may occur.
Rub in direction of grain to avoid damaging.

Stainless Steel Cleaner & Polish (not included):

See “Assistance or Service” section to order.

Liquid detergent or all-purpose cleaner:

Rinse with clean water and dry with soft, lint-free cloth.

Vinegar for hard water spots

CONTROL KNOBS

Do not use steel wool, abrasive cleansers or oven cleaner.
Do not soak knobs.
When replacing knobs, make sure knobs are in the Off position.
On some models, do not remove seals under knobs.

Soap and water or dishwasher:

Pull knobs straight away from control panel to remove.

PORCELAIN-COATED GRATES AND CAPS

Food spills containing acids, such as vinegar and tomato, should 
be cleaned as soon as the cooktop, grates and caps are cool. 
These spills may affect the finish.
To avoid chipping, do not bang grates and caps against each 
other or hard surfaces such as cast iron cookware.
Do not reassemble caps on burners while wet.
Do not clean in the Self-Cleaning cycle.

Nonabrasive plastic scrubbing pad and mildly abrasive 
cleanser:

Clean as soon as cooktop, grates and caps are cool.

Dishwasher (grates only, not caps):

Use the most aggressive cycle.

SURFACE BURNERS

Sealed Burner models

See “Sealed Surface Burners” section.
Open Burner models

See “Surface Burners” section.

CERAMIC GLASS 

(on some models)

Do not use steel wool, abrasive powder cleansers, chlorine 
bleach, rust remover or ammonia because damage may occur.
Always wipe with a clean, wet cloth or sponge and dry thoroughly 
to prevent streaking and staining.
Cooktop Polishing Creme is recommended for regular use to help 
prevent scratches, pitting and abrasions, and to condition the 
cooktop. It may be ordered as an accessory. See “Assistance or 
Service” to order.
A Cooktop Scraper is also recommended for stubborn soils, and 
can be ordered as an accessory. See “Assistance or Service” to 
order. The Cooktop Scraper uses razor blades. Store razor 
blades out of the reach of children.

Light to moderate soil

Paper towels or clean damp sponge:

Clean while the cooktop is still warm. You may want to wear 
oven mitts while doing so.

Sugary spills (jellies, candy, syrup)

Cooktop Scraper:

Clean while the cooktop is still warm. You may want to wear 
oven mitts while doing so.

Cooktop Polishing Creme and clean damp paper towel:

Clean as soon as cooktop has cooled down. Rub creme into 
surface with a damp paper towel or soft cloth. Continue 
rubbing until white film disappears.

Heavy soil, dark streaks, specks and discoloration

Cooktop Polishing Creme or nonabrasive cleanser:

Rub product into soil with a damp paper towel or soft cloth. 
Continue rubbing until white film disappears.

Burned-on soil

Cooktop Polishing Creme and Cooktop Scraper:

Rub creme into soil with damp paper towel. Hold scraper as 
flat as possible on surface and scrape. Repeat for stubborn 
spots. Polish entire cooktop with creme and paper towel.

Metal marks from aluminum and copper

Cooktop Polishing Creme:

Clean as soon as cooktop has cooled down. Rub creme into 
surface with a damp paper towel or soft cloth. Continue 
rubbing until white film disappears. The marks will not totally 
disappear but after many cleanings become less noticeable.

Tiny scratches and abrasions

Cooktop Polishing Creme:

Rub creme into surface with a damp paper towel or soft cloth. 
Continue rubbing until white film disappears. Scratches and 
abrasions do not affect cooking performance and after many 
cleanings become less noticeable.

Summary of Contents for KGRC608





























Reviews: