KitchenAid KGCT366E Use & Care Manual Download Page 4

IMPORTANT SAFETY INFORMATION

Fire Hazard

Do not obstruct the flow of combustion and
ventilation air.

Electrical Shock Hazard

It is the customer’s responsibility to.

• Contact a qualified electrical installer.
• Assure that electrical installation is adequate

and in conformance with the National Electri-
cal Code, ANSI/NFPA 70—latest edition•,
and all local codes and ordinances.

• Take special care when drilling holes into the

wall for venting or electrical wiring. Electrical
wires may be concealed behind the wall cov-
ering.

• Disconnect the power to any electrical circuits

that could be affected by the installation of this
cooktop.

Failure to do so could result in fire, electrical
shock, or other personal injury.

Personal Injury Hazard

To eliminate the risk of burns or fires, do not
install cabinets or store things above the cooktop.
If cabinets are already installed above the
cooktop, install a range hood to the bottom of the
cabinet to prevent reaching over the heated
cooking surface. The range hood should stick
out a minimum of 5-inches (12.7 cm) from the
front of the cabinets.

Reaching over a heated cooking surface could
result in a serious burn or other inury.

• Copies of the standards listed above may be

obtained from:

National Fire Protection Association
Batterymarch Park
Quincy, Massachusetts 02269

This Job Aid is intended for factory-service techni-
cians only. We recommend that customers DO
NOT service their own units, because of the com-
plexity and risk of high-voltage electrical shock

If the information in this Job Aid is not fol-
lowed exactly, a fire or explosion may result
causing property damage, personal injury or
death:

Do Not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Do Not try to light any appliance.
• Do Not touch any electrical switch; Do Not use

any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s
instructions.

• If you cannot reach your gas supplier, call the

fire department.

Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.

WARNING

WARNING

Summary of Contents for KGCT366E















Reviews: