Page 1
4 screws (double oven)
Phillips
screwdriver
Product dimensions
Cutout dimensions
Before you start...
49-1/2"
recessed
height
51" max.
overall
height
22-3/8" max.
recessed width
23" max.
recessed
depth
23-3/4"
overall width
Double oven
Single oven
27-1/2"
recessed
height
22-3/8" max.
recessed
width
23" max.
recessed
23-3/4"
overall width
29" max.
overall
height
24" min.
cabinet
1" top of cutout
to bottom of
upper cabinet
door
24" min.
cabinet width
24" min.
cabinet width
22-1/2"
cutout
width
22-1/2"
cutout
width
49-3/4"
min.
cutout
height
14-3/4"
bottom
of cutout
to floor
1-1/2" min.
bottom of
cutout to top of
cabinet door
22-1/2"
cutout width
5-1/4" bottom of
cutout to floor
27-3/4"
min.
cutout
height
1-1/2" min.
top of cutout
to underside
of countertop
1" top of cutout
to bottom of
upper cabinet
door
1-1/2"
min.
bottom of
cutout to
top of
cabinet
door
32"
bottom of
cutout to
floor
Single oven
undercounter
(without cooktop
installed above)
Double oven
Cabinet side view
Single oven
27-3/4"
min.
cutout
height
23-1/4" min.
cutout depth
23" recessed
oven depth
recessed
oven
cabinet
oven
front
Important: Observe all governing codes
and ordinances.
Proper installation
is your responsibility.
Have a qualified technician install this oven.
Oven location
should be away from strong draft
areas, such as windows, doors and strong
heating vents.
Cabinet opening dimensions
that are shown
must be used. Given dimensions provide
minimum clearance.
Recessed installation area
must provide
complete enclosure around the recessed portion
of the oven.
Electrical ground
is required. See “Electrical
requirements.”
Electrical supply junction box
should be located
3 inches maximum below the support surface
when oven is installed in a wall cabinet. Drill a
1-inch minimum diameter hole in the right rear
or left rear corner of the support surface to pass
the appliance cable through to the junction box.
For undercounter installation, it is recommended
that the junction box be located in the adjacent
right or left cabinet. If installing the junction box
on rear wall behind oven, junction box
must be
recessed
and located in the upper or lower right
or left corner of cabinet.
Oven support surface
MUST be solid, level and
flush with bottom of cabinet cutout.
It is the customer’s responsibility:
To contact a qualified electrical installer.
To assure that the electrical installation is
adequate and in conformance with National
Electrical Code, ANSI/NFPA 70 — latest edition*,
and all local codes and ordinances.
Copies of the standards listed may be obtained from:
* National Fire Protection Association
Batterymarch Park
Quincy, Massachusetts 02269
Tool needed:
Parts supplied:
Your safety and the safety of others are
very important.
We have provided many important safety
messages in this manual and on your appliance.
Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards
that can kill or hurt you and others.
All safety messages will follow the safety alert
symbol and either the word “DANGER” or
“WARNING”. These words mean:
All safety messages will tell you what the potential
hazard is, tell you how to reduce the chance of
injury, and tell you what can happen if the
instructions are not followed.
You can be killed or seriously injured if you don’t
immediately follow instructions.
You can be killed or seriously injured if you don’t
follow instructions.
WARNING
DANGER
