KitchenAid KCIP 1010/I Instructions For Use Manual Download | Manualshive

Page: 8 / 20

background image

T recirculation

mode

SIDE VIEW

Deflector

Connection

ring

Exhaust

Vent

Pipe

Recirculation mode only

Fig. 4

• Recirculation mode only: fix the deflector to the

frame:

a.

Insert the deflector from one side of the

frame so that the rectangular hole at the centre
is facing downwards.

b.

Fit the deflector with 4 screws from the top

of the frame.

c.

Connect a suitable extraction pipe to the

connection ring provided. It should be long
enough ( with a diameter of 150mm) to reach
the connection ring on the motor unit when it is
installed. Use the mathematical formula in the
diagram to do this.

d.

Insert the pipe with the connection ring

upwards and fix it to the deflector with 2 screws.

Installation

8

«
...
6
7
8
9
10
...
»

Summary of Contents for KCIP 1010/I





















Reviews:

No comments

Related manuals for KCIP 1010/I

Brand: Jenn-Air Pages: 40

30" (76.2 cm) Cooktop

Brand: Jenn-Air Pages: 32

Brand: FALMEC Pages: 64

Brand: Zline Pages: 43

Brand: FALMEC Pages: 80

Brand: FALMEC Pages: 96

Brand: FALMEC Pages: 80

Brand: FALMEC Pages: 1

Brand: NEFF Pages: 20

Brand: NEFF Pages: 24

Brand: Kuppersbusch Pages: 17

KX-TN 90 IX/GLASS

Brand: Zirtal Pages: 44

Brand: Bertazzoni Pages: 68

tastic LUMINATE 34401

Brand: IXL Pages: 2

Brand: Jenn-Air Pages: 40

Brand: Vallox Pages: 4

Brand: ROBLIN Pages: 60

Brand: NEFF Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands