![background image](http://html.mh-extra.com/html/kitchenaid/architect-ii-kers206x/architect-ii-kers206x_user-manual_198040027.webp)
27
As soon as Self Clean becomes active, a motor driven
lock mechanism will begin locking the oven door
automatically, and
door Loc
will appear in the display
(See Fig. 1).
DO NOT
open the oven door when
door
Loc
is displayed (allow 15 seconds for the lock
mechanism to lock the oven).
Once the oven door has locked,
CLn
will appear in the
display indicating Self Clean has started (Fig. 2).
Self Clean
Fig. 1
Fig. 2
When Self Clean is finished:
Use caution when opening the oven
door after self-cleaning
. The oven may still be
VERY
HOT and can cause burns
. To avoid possible burns
stand to the side of the oven when opening the oven door
to allow hot air or steam to escape.
1.
CLn
message will turn off and
Hot
will appear in display
window (See Fig. 3).
2. Once the oven has cooled down (about 1 hour) and
Hot
is no longer displayed the
door OPn
message will
appear (Fig. 4).
When this message turns off the
oven door may be opened
.
3. When the oven interior has completely cooled, wipe
away any residue or powdered ash with a damp cloth or
paper towel.
Important notes:
The kitchen area should be well ventilated using an
open window, ventilation fan or exhaust hood during the
1st self-clean cycle. This will help eliminate the normal
odors associated with the 1st self-clean cycle.
When the clean time finishes the oven door will remain
locked until the range has cooled sufficiently.
In
addition to the clean time that was programmed,
you must allow about 1 additional hour for the oven
to cool before you will be able to open the oven
door.
The Self Clean function will not operate whenever a
radiant surface element is ON or the Control Lock is
active.
Fig. 3
Fig. 4
Delayed Start Self Clean
Example To start a delay Self Clean with
default clean time of 3 hours and a start time of
9:00 oclock:
1. Be sure the clock is set with the correct time of day, the
oven is empty and ALL oven racks are removed. Be
sure oven door is completely closed.
2. Press
Delay Start
keypad.
3. Using numeric keypad enter
9 0 0
for time to start.
4. Press
START
to accept.
5. Press
Self Clean
keypad.
6. Press
START
.
If it is necessary to stop Self Clean when active:
1. Press
OFF
.
2. If Self Clean has heated the oven to a high
temperature, allow enough time for the oven to cool and
for the
door OPn
message to appear (Fig. 4). When
this message turns OFF the oven door may be opened.
3. Restart Self Clean if needed.
Important notes:
When Self Clean function is active you may check the
amount of clean time remaining by pressing the Self
Clean keypad once.
If your control is set with the default 12 hour display
mode, the Delay Self Clean can only be set to start up to
11 hours and 59 minutes in advance. To set a Delay
Start Self Clean to begin 12 or more hours (maximum is
23 hours and 59 minutes) in advance, be sure to set the
control for 24 hour display mode.
If Self Clean is active and then interrupted by power
failure or cancelled before the oven was thoroughly
cleaned, it may be necessary to run a self-clean cycle
again.
If the oven temperature was high enough
when interrupted you may need to allow up to 4
hours for the oven to cool before Self Clean can be
started again.
Summary of Contents for ARCHITECT II KERS206X
Page 1: ...Models Modèles KERS206X KERS208X W10328277A 316902700 ...
Page 36: ......