KISAN NEWTON K5, Quick Start Manual, Page: 2 / 2

ADDITIONAL BILL-HANDLING PROCEDURES:
FACING BILLS: (IN "MIX" MODE)

PRESS THE MODE KEY UNTIL YOU SEE THE WORD " VALUE " IN THE UPPER LEFT OF THE SCREEN NEXT TO THE FLAG.

TAP THE “ DENOM ” KEY UNTIL YOU SEE THE WORD “ MIX ” IN EACH COUNT WINDOW ON THE SCREEN.

HOLD DOWN THE MODE KEY FOR A COUPLE SECONDS UNTIL THE MODE SCREEN POPS UP

TAP THE BOX WITH THE WORD " FACE " AND IT WILL LIGHT UP

PRESS THE " ACCEPT " BUTTON TO RETURN TO THE MAIN SCREEN

YOU WILL SEE “ FACE ” NEAR THE TOP RIGHT OF THE SCREEN TO INDICATE FACING IS TURNED ON

SCANS FIRST BILL AND PUTS ALL BILLS WITH THAT FACE IN THE TOP POCKET. BILLS WITH THE OTHER FACE ARE PUT IN TO
THE SECOND POCKET. IF ANY POCKET REACHES A BATCH TOTAL, THE MACHINE THEN USES THE NEXT AVAILABLE POCKET,
AND SO ON.

REMOVE THE STACK(S) AND ALIGN ACCORDINGLY

ALL BILLS ARE NOW FACED.

IF ANY BILLS ARE REJECTED (BAD, SOILED, COUNTERFEIT), YOU CAN CHECK THE REASON BY TAPPING ON “ REJ ” ON THE
BOTTOM RIGHT OF THE SCREEN (YOU MUST DO SO BEFORE YOU REMOVE THE BILLS)
***NOTE : AFTER RUNNING; MAKE SURE TO UNSELECT " FACE " SETTING WHEN FINISHED FACING ***
ORIENT BILLS: (IN "MIX" MODE)

PRESS THE MODE KEY UNTIL YOU SEE THE WORD " VALUE " IN THE UPPER LEFT OF THE SCREEN NEXT TO THE FLAG.

TAP THE “ DENOM ” KEY UNTIL YOU SEE THE WORD “ MIX ” IN EACH COUNT WINDOW ON THE SCREEN.

HOLD DOWN THE MODE KEY FOR A COUPLE SECONDS UNTIL THE MODE SCREEN POPS UP

TAP THE BOX WITH THE WORD " ORIENT " AND IT WILL LIGHT UP

PRESS THE " ACCEPT " BUTTON TO RETURN TO THE MAIN SCREEN

YOU WILL SEE “ ORIENT ” NEAR THE TOP RIGHT OF THE SCREEN TO INDICATE ORIENTATION IS TURNED ON

SCANS FIRST BILL AND PUTS ALL BILLS WITH THAT ORIENTATION IN THE TOP POCKET. BILLS WITH THE OTHER ORIENTATION
ARE PUT IN TO THE SECOND POCKET. IF ANY POCKET REACHES A BATCH TOTAL, THE MACHINE THEN USES THE NEXT
AVAILABLE POCKET, AND SO ON.

REMOVE THE STACK(S) AND ALIGN ACCORDINGLY

ALL BILLS ARE NOW ORIENTED.

IF ANY BILLS ARE REJECTED (BAD, SOILED, COUNTERFEIT), YOU CAN CHECK THE REASON BY TAPPING ON “ REJ ” ON THE
BOTTOM RIGHT OF THE SCREEN (YOU MUST DO SO BEFORE YOU REMOVE THE BILLS)
***NOTE : AFTER RUNNING; MAKE SURE TO UNSELECT " ORIENT " SETTING WHEN FINISHED ORIENTING ***
MIXED BILL SORTING: (AUTOMATIC)

PRESS THE MODE KEY UNTIL YOU SEE THE WORD " VALUE " IN THE UPPER LEFT OF THE SCREEN NEXT TO THE FLAG.

TAP THE “ DENOM ” KEY UNTIL YOU SEE THE WORD “ AUTO ” IN EACH COUNT WINDOW ON THE SCREEN.

SCANS 1ST BILL GOING THROUGH AND COUNTS ALL BILLS OF THAT DENOMINATION TO THE FIRST POCKET. WHEN IT SCANS A
SECOND DENOMINATION, IT SENDS ALL BILLS OF THAT DENOMINATION TO THE SECOND POCKET, AND SO ON FOR
SUBSEQUENT DENOMINATIONS.

BATCHING CAN BE PERFORMED AT THIS TIME FOR STRAPPING BILLS.

TAP THE “ BATCH ” BUTTON ON THE SCREEN TO CYCLE THROUGH THE PRESET BATCH QUANTITIES. THIS SETS THE SAME
QUANTTY FOR EVERY POCKET.

TO SET DIFFERENT QUANTITIES FOR EACH POCKET, HOLD THE “ BATCH ” KEY FOR A COUPLE SECONDS UNTIL THE SCREEN
CHANGES. TAP THE POCKET (A,B,C, D) YOU WISH TO CHANGE, THEN TYPE IN THE QUANTITY YOU WANT IN THAT POCKET.
YOU CAN SET EACH POCKET INDIVIDUALLY. TAP “
ACCEPT ” TO SAVE.

IF ANY BILLS ARE REJECTED (BAD, SOILED, COUNTERFEIT), YOU CAN CHECK THE REASON BY TAPPING ON “ REJ ” ON THE
BOTTOM RIGHT OF THE SCREEN (YOU MUST DO SO BEFORE YOU REMOVE THE BILLS)
***NOTE : PRIOR TO RUNNING; MAKE SURE “ FACE " AND/OR " ORIENT " SETTINGS ARE TURNED OFF ***
BATCH COUNTING
CYCLING THROUGH BATCH PRESETS

TAP THE “ BATCH ” KEY AND YOU WILL SEE THE BATCH AMOUNT CHANGE ON THE SCREEN FOR EACH POCKET. THERE ARE SIX
PRESETS FOR BATCHING. THE DEFAULT SETTINGS ARE 10-20-50-100-150-200.
CHANGING BATCH PRESETS

HOLD THE “ MENU ” KEY DOWN FOR A COUPLE SECONDS UNTIL YOU SEE THE SCREEN CHANGE. TYPE 0 9 8 7 AND THEN TAP
“ ACCEPT ”. ON THE NEXT SCREEN, TAP “ CONFIG ”, THEN ON THE NEXT SCREEN TAP “ BATCH ”

TAP WHICH BATCH AMOUNT YOU WANT TO CHANGE (OR USE UP/DOWN ARROW BUTTONS). TYPE THE NEW AMOUNT ON THE
KEYPAD, THEN TAP “
OK ”. TAP “ ACCEPT ” WHEN YOU’RE DONE. TAP “ BACK ” TWICE TO GO BACK TO THE MAIN SCREEN.

NOW, WHEN YOU TAP “ BATCH ”, YOU CAN SCROLL THROUGH THE NEW BATCH NUMBERS YOU ENTERED
CHANGING BATCH AMOUNTS FOR ONE TIME USE

HOLD THE “ BATCH ” KEY DOWN FOR A COUPLE SECONDS UNTIL YOU SEE THE SCREEN CHANGE.

TAP WHICH BATCH AMOUNT YOU WANT TO CHANGE (OR USE UP/DOWN ARROW BUTTONS). TYPE THE NEW AMOUNT ON THE
KEYPAD, THEN TAP “
ACCEPT ” WHEN YOU’RE DONE.

YOU WILL SEE THE NEW BATCH NUMBERS SHOWN ON SCREEN FOR EACH POCKET YOU CHANGED.

AS SOON AS YOU SCROLL THROUGH THE BATCHES AGAIN, THE CHANGES YOU MADE ARE ERASED AND THE MACHINE GOES
BACK TO THE PROGRAMMED PRESETS.