manualshive.com logo in svg

Kirkland Signature 720-0432, Operating Instructions Manual

Share
Download
Kirkland Signature 720-0432 Operating Instructions Manual Download Page 39

Rotisserie motor will not turn 

--Check the voltage at the outlet.
--If an extension cord is required, ensure it is a 16 gauges, 
grounded cord.
--Ensure the on/off switch is on.
--Ensure the load does not exceed the 40 pounds operational 
capacity.
--Ensure the spit is fully inserted in the motor.
--Ensure there is no encumbrance or drag. 

Grill only heats to 200-300 degrees. 

--Ensure the temperature gauge is functioning properly. Hold 
a flame to the probe or compare the grill gauge to an oven 
thermometer place in the grill.
--Ensure correct start procedure. Prior to lighting grill, the gas
control knobs should be off. The propane bottle should be 
off. If not, wait 15 minutes. Turn tank all the way on.. Turn 
left burner to ignite, wait 5 seconds ignite. Repeat for 
additional burners.
--Check all gas connections for leaks with bubble test. If 
leaks are found, replace the part or tighten the fitting.
--If it is a natural gas grill, ensure there is proper pressure to
the grill. Refer to the user manual. Example: Gas line stubbed 
off o pool heater may exhibit deference in pressure.    .

Grill takes a long time to preheat. 

--Normal preheat 500-600degrees, takes about 10-15 min. 
Cold weather and wind may effect your preheat time.
--If you are using volcanic rock or briquettes they can 
increase the preheat time and maximum temperature. 

Burner flames are not light blue. 

--Too much or not enough air mixes for the flame. 
--Elevation is the principal cause, however cold weather
can affect the mixture. Burner adjustment may be
required. --Grill is in a windy location.   

TROUBLE SHOOTING

A16Y07P-1    35

Summary of Contents for 720-0432





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands