Kino Flo Image L40 Retrofit Instructions Manual Download Page 13 | Manualshive

Page: 13 / 19

background image

13

Install diffuser panel as shown and align with pre-drilled holes.

Do not peel off liner completely. Start peeling liner in one corner to expose a screw

point and loosely hand tighten screw (P/N 2020159). Continue to peel liner to next

screw point and loosely hand tighten screw and so on until eight (8) screws have

been hand tightened.

«
...
11
12
13
14
15
...
»

Summary of Contents for Image L40 Retrofit




















Reviews:

No comments

Related manuals for Image L40 Retrofit

Brand: Ledvance Pages: 2

Brand: Wacker Neuson Pages: 110

Brand: Xtricity Pages: 4

Brand: GE Pages: 2

Brand: EuroLite Pages: 2

Brand: Meec tools Pages: 24

EPL-WPLED-100W-RT

Brand: Larson Electronics Pages: 3

Brand: Intermatic Pages: 2

Brand: Kemot Pages: 32

Brand: LARSON Pages: 8

Brand: Blizzard Lighting Pages: 20

Brand: Bebe Sounds Pages: 1

Brand: ProLights Pages: 44

LivingColors 6917155PU

Brand: Philips Pages: 3

LivingColors 6917155PH

Brand: Philips Pages: 3

LivingColors 6916665PH

Brand: Philips Pages: 3

LivingColors 6917130PU

Brand: Philips Pages: 3

LivingColors 6917130PH

Brand: Philips Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands