Kino Flo CEL-200C-120U Operation Manual Download Page 17

Page: 17 / 20

LVR-CE290-P

Celeb 200 Louver/HP 90°

LVR-CE260-P

Celeb 200 Louver/HP 60°

MTP-B41F

Kino Offset w/ Baby Receiver (16mm)

Lollipops are interchangeable.

MTP-L

Kino 41 Lollipop w/ 3/8” Pin (10mm)

MTP-LB

Kino 41 Lollipop w/ Baby Receiver (16mm)

MTP-LBS

Kino 41 Lollipop w/ Baby Receiver Short

(16mm)

Accessories

BRD-CE2

Celeb 200 Barndoors (Set of 4)

GFR-CE2

Celeb 200 Gel Frame

Troubleshooting continued

Can’t set the DMX address.

You must Press and Hold the DMX Address button for 3 seconds in order to

select an address. The display will flash while in edit mode. Select a valid

address from 1-512. (Note: 0 or 513 and higher are invalid addresses.)

Can’t operate the fixture manually with the DMX cable plugged in.

Two Options:

Set DMX address to “0” or disconnect cable and turn power off and on.

Summary of Contents for CEL-200C-120U





















Search results

Summary of Contents for CEL-200C-120U

Reviews:

Related manuals for CEL-200C-120U

Brands by name

Popular brands

Kino Flo CEL-200C-120U, Operation Manual

Search results

Summary of Contents for CEL-200C-120U

Reviews:

Related manuals for CEL-200C-120U

Brands by name

Popular brands