background image

Both brushes should be replaced at the same time. Use only identical carbon 
brushes. Use a screwdriver to remove the brush holder caps. Take out the worn 
carbon brushes, insert the new ones and secure the brush holder caps. 
 

TIPS FOR MAINTAINING MAXIMUM BATTERY LIFE 

1.

 

Charge the battery pack before battery is completely discharged. 
Always stop tool operation and charge the battery pack when you notice 
less tool power. 

2.

 

Never recharge a fully charged battery pack. Overcharging shortens the 
battery service life.   

3.

 

Charge the battery pack at room temperature 40ºF - 105ºF. Let a hot battery 
pack cool down before re-charging it.   

 

                       

 
 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 

LIMITED WARRANTY 

Thank you for purchasing a top quality

 KingCraft

 product. This Cordless Circular Saw item 

#3729 was tested and meets our stringent quality standards. This product is warranted to be 

free from manufacturing defects in original materials, including original parts, and 

workmanship until Oct 18

th

. 2005 or 1 year with proof of purchase. 

 

The warranty is void if the defect is due to accidental damage, misuse, abuse, neglect, 

improper repair or alteration by unauthorized persons or failure to follow operation 

instructions provided with the product. This warranty does not apply to commercial use. 

 

The warranty is non-transferable and applies only to the original purchase and does not 
extend to subsequent owners of the product. Liability under this warranty is limited to repair, 
replacement or refund. In no event shall liability exceed the purchase price paid by the 
purchaser of the product. Under no circumstances shall there be liability for any loss, direct, 
indirect, incidental, special or consequential damage arising out of in connection with use of 
this product. This warranty is valid only in the United States of America. This Warranty gives 
you specific legal rights. However you may have other rights that vary from state to state. 
Some states do not allow limitation on implied warranties or exclusion of consequential 
damages therefore these restrictions may not apply to you. 
In case you find the product to be defective please send it within the warranty period to our 
service center, To avoid transport damages please send the product in the original packaging. 
In return you will receive either your repaired item, a new product or a refund. Please fill out 
the Warranty Card and send it together with the product and purchase receipt 

 

To arrange pick-up of the defective item please call our service center: 

 

Schenker International Inc. 

Tel: 1-888-367-7373 (Business hours Mon-Fri 9:00am-4:00 pm CT) 

Website: 

http://www.wk-usa.com

 

Wachsmuth& Krogmann,Inc. 

123 Sivert Court, 

Bensenville,IL 60106, 

USA                                             

22 

21 

Summary of Contents for PCSD180T













Reviews: