manualshive.com logo in svg

KING 5780/14, Original Instructions Manual, Page: 26 / 33

Share
Download
KING 5780/14 Original Instructions Manual Download Page 26

ORIGINAL INSTRUCTIONS

  

 

 

Model:

 Dispenser Rx 

Serial Number: 

5780/14

 

 

 

Instructions Manual Dispenser Rx Tablet and Capsule Counting Machine Edition v2.1 

 

 

26 

OPERATION: Correct Bottle Platform Adjustment  

 

 

 

•

  To adjust the 

BOTTLE PLATFORM

 first loosen the 

CLAMPING HANDLE

 to allow the 

BOTTLE PLATFORM

 free movement.

 

 

•

  Using two bottles manually adjust the height of the 

BOTTLE PLATFORM

 using the 

CLAMPING HANDLE

 located on the right underside to achieve a small gap between the 

underside of the funnel and the top of the bottle neck opening. Leaving a small gap of 

between 2mm and 3mm between the underside of the funnel and neck opening of the 

bottle facilitates easy placement and removal of bottles during operation.  

 

•

  Proceed to tighten the 

CLAMPING HANDLE

 once the 

BOTTLE PLATFORM

 is located in 

the correct position.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bottle Platform 

Clamping Handle 

Funnel 

2mm to 3mm gap 

Summary of Contents for 5780/14


































Reviews:

No comments