13
This Cycler is designed to work effectively with a variety of pool equipment as long as the following procedures are followed.
Set the control dial by matching up the parameters of your pool on the chart below. THIS IS A STARTING POINT ONLY and may need
to be adjusted to fi t your individual pool needs. See #2 below for adjusting directions.
IMPORTANT:
If using a multi-speed pump,
pump-run times of at least 6 hours per day at high speed are recommended for proper performance.
If running the pump at low speed only or on high speed less than 6 hours, please follow the 24 hour low-speed
directions below.
POOL SIZE
Gallons Diameter
8 HOUR PUMP RUN TIME
12 HOUR PUMP RUN TIME
24 HOUR PUMP RUN TIME
PUMP SIZE
1/2 hp 3/4 hp 1 hp 1 1/2 hp
PUMP SIZE
1/2 hp 3/4 hp 1 hp 1 1/2 hp
PUMP SIZE
1/2 hp 3/4 hp 1 hp 1 1/2 hp
7,000 (18’)
5.0
4.5
4.0
3.5
4.5
4.0
3.0
5.0*
3.5
3.0
2.5
4.0*
9,000 (21’)
5.5
5.0
4.5
4.0
5.0
4.5
4.0
5.5*
4.0
3.5
3.0
4.5*
12,000 (24’)
6.0
5.5
5.0
4.5
5.5
5.0
4.5
4.0
4.5
4.0
3.5
5.0*
15,000
NR
6.0
5.5
5.0
6.0
5.5
5.0
4.5
5.0
4.5
4.0
3.5
20,000
NR
NR
6.0
5.5
NR
6.0
5.5
5.0
5.5
5.0
4.5
4.0
25,000
NR
NR
6.5
6.0
NR
6.5
6.0
5.5
6.0
5.5
5.0
4.5
POOL SIZE
Gallons Diameter
12 HOUR PUMP RUN TIME
PUMP SIZE
1/2 hp 3/4 hp 1 hp 1 1/2 hp
7,000 (18’)
4.5
4.0
3.0
5.0*
9,000 (21’)
5.0
4.5
4.0
5.5*
12,000 (24’)
5.5
5.0
4.5
4.0
15,000
6.0
5.5
5.0
4.5
20,000
NR
6.0
5.5
5.0
25,000
NR
6.5
6.0
5.5
Step 3: Setting the Control Dial
1.
24 HOUR, LOW-SPEED PUMP-RUN TIME
In order to ensure proper performance when running the
pump on low speed for 24 hours per day or high speed less
than 6 hours per day, bleed the air while the pump is on by
unscrewing the knob on the back of the Cycler near the cap
until water appears. Then screw the knob back on. Repeat this
process each time the cap is removed for any reason. Set the
control dial at 6 and follow the adjustment directions in Step 2
to determine the correct setting for your pool.
For the fi rst week, test the pool water
daily for free chlorine with FROG Test
Strips to ensure correct dial setting.
Continue to test weekly throughout
the season.
IMPORTANT:
Control dial settings in excess of these
recommendations could result in excess trichlor levels being
discharged into the pool. This can result in bleaching or
discoloration of areas around the pool inlet or, in some cases,
bleaching or discoloration of the entire pool liner or paint. In
addition, excess trichlor in the pool can create health hazards
to bathers.
2.
After each testing, adjust the dial
up by 1/2 increment if the free
chlorine reading has dropped
below 0.5 ppm or adjust down by
1/2 increment if the reading has
risen above 1.0 ppm. Continue
this process each day until the free
chlorine reading stabilizes to at
least 0.5 ppm.
Remember to adjust dial by
1/2 increments only in order to
prevent over chlorination which
may bleach pool surfaces.
* –
Bypass installation recommended. NR – This pump size is not recommended for this size pool.
Find your starting dial setting by matching up the parameters of your
pool on the above chart. An above ground pool with approximately
12,000 gallons, with a 1 horsepower pump running 12 hours a day,
would require a starting setting of 4.5.
RECOMMENDED FLOW RATE: 20-60 gpm
Ope
ra
te
EXAMPLE
