King-Meter KM6S-LCD User Manual Download

Page: 8 / 38

KING-METER TECHNOLOGY CO., LTD

No.15, Chenchang Road, Beichen Dist.Tianjin,300134, CN

Fax

：

+0086 022 8478 0358 Tel: +0086 022 8478 0378

- 5 -

4. Installation Instruction

Fix the display on the handlebar, adjust the angel. Plug the two connectors

from display and controller when off power supply.

Standard Connector Wire Sequence

Connect to the controller

Display Outlet

Connection Interface

Table: Standard connector wire sequence

Standard
Wiring

Standard Wiring Color

Function

Red(VCC)

Display power Wire

Blue(K)

Controller Power Control Wire

Black(GND)

Display Ground Wire

Green(RX)

Display Data Receiving Wire

Yellow(TX)

Display Data Transmission Wire

Note: Some products have waterproof connectors for the leads, and the user cannot see

the color of the leads in the harness.

5.User Setting

5.1 Power On/Off

Hold

MODE

button to start display and supply power to the controller. When

at working state, press and hold

MODE

to shut off E-bike power. In the off state,

the display no longer uses the battery's power supply; leakage current is less than

1uA.

If you do not use the E-bike for more than 10 minutes, the display will

turn off automatically.

Summary of Contents for KM6S-LCD







































Search results

Summary of Contents for KM6S-LCD

Reviews:

Related manuals for KM6S-LCD

Brands by name

Popular brands

King-Meter KM6S-LCD, User Manual

Search results

Summary of Contents for KM6S-LCD

Reviews:

Related manuals for KM6S-LCD

Brands by name

Popular brands