background image

ASSEMBLY 
 
ATTACHING WORK LIGHT HEAD TO BASE 

Place the base (A) Fig.4 on a flat surface. Position 
the U-Shape bracket (B) of the work light head onto 
the base (A) as shown in Fig.4. Use the lock knob 
(C), flat washer and spring washer to secure the 
work light head on the base.  
 

OPERATION 
 
ADJUSTING THE LIGHT DIRECTION

 

Your work light can be tilted vertically up to 30° down 
or 90° up. To adjust the light direction, loosen the 
side locking knobs (D) Fig.4. Adjust the work light 
head to desired position, and retighten knobs. 
 

ON/OFF SWITCH

 

Your work light is equipped with a weather protected 
sealed ON/OFF switch (A) Fig.5 located on the back 
side of the work light. Press the switch once to turn 
the work light on and press the switch a second time 
to turn it off. Always turn the work light off before 
unplugging from power source. 
 

MAINTENANCE & SERVICE 

 

Your work light requires very little care and         
maintenance. Simply clean the lens regularly with a 
non-abrasive cleaner. Use similar care for the base 
and U-bracket. When servicing, use only identical 
parts.  Use of any other parts may create a hazard 
or cause product damage. Contact a King Canada service centre for identical    
replacement parts. 
 

WARNING:

 Always make sure the work light is unplugged and completely cool before 

attempting to clean it. 
 

RECYCLING 

 

Do not dispose of electrical appliances as unsorted municipal waste, use separate     
collection facilities. Contact you local government for information regarding the collection 
systems available. If electrical appliances are disposed of in landfills or dumps, hazardous 
substances can leak into the groundwater and get into the food chain, damaging your 
health and well-being. 

ASSEMBLY, OPERATION 

& MAINTENANCE

FIGURE 4

FIGURE 5

PARTS DIAGRAM & PARTS LISTS

 

Refer to the Parts section of the King Canada web site for the most updated parts diagram 
and parts list.

Summary of Contents for KC-1501LED








Reviews: