King Canada 9999 ITM Instruction Manual Download Page 3

GENERAL SAFETY INSTRUCTIONS

FOR ELECTRIC SNOW THROWERS

GENERAL SAFETY INSTRUCTIONS

1. KNOW YOUR TOOL.

Read and understand the owner’s manual and labels affixed to the tool.
Learn its application and limitations as well as its specific potential
hazards. 

2. KEEP GUARDS IN PLACE.

Keep in good working order, properly adjusted and aligned.

3. REMOVE ADJUSTING KEYS AND WRENCHES.

Form habit of checking to see that keys and adjusting wrenches are
removed from tool before turning it on.

4. KEEP WORK AREA CLEAN.

Cluttered areas and benches invite accidents. Make sure the floor is
clean and not slippery due to wax and sawdust build-up. 

5. AVOID DANGEROUS ENVIRONMENT.

Don’t use power tools in damp or wet locations or expose them to rain.
Keep work area well lit and provide adequate surrounding work space.

6. KEEP CHILDREN AWAY.

All visitors should be kept a safe distance from work area.

7. MAKE WORKSHOP CHILD-PROOF.

Make workshop child-proof with padlocks, master switches or by
removing starter keys.

8. USE PROPER SPEED.

A tool will do a better and safer job when operated at the proper speed.

9. USE RIGHT TOOL.

Don’t force the tool or the attachment to do a job for which it was not
designed.

10. WEAR PROPER APPAREL.

Do not wear loose clothing, gloves, neckties or jewelry (rings, watch)
because they could get caught in moving parts. Non-slip footwear is
recommended. Wear protective hair covering to contain long hair. Roll
up long sleeves above the elbows.

11. ALWAYS WEAR SAFETY GLASSES.

Always wear safety glasses (ANSI Z87.1). Everyday eyeglasses only
have impact resistant lenses, they are not safety glasses. Also use a
face or dust mask if operation is dusty.

12. DON’T OVERREACH.

Keep proper footing and balance at all times.

13. MAINTAIN TOOL WITH CARE.

Keep tools sharp and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.

14. DISCONNECT TOOLS.

Before servicing, when changing accessories or attachments.

15. AVOID ACCIDENTAL STARTING.

Make sure the swich is in the ‘’OFF’’ position before plugging in.

16. USE RECOMMENDED ACCESSORIES.

Consult the manual for recommended accessories. Follow the
instructions that accompany the accessories. The use of improper
accessories may cause hazards.

17. NEVER STAND ON TOOL.

Serious injury could occur if the tool tips over. Do not store materials
such that it is necessary to stand on the tool to reach them.

18. CHECK DAMAGED PARTS.

Before further use of a tool, the guard or other parts should be
carefully checked to ensure that they will operate properly and perform
their intended function. Check for alignment of moving parts, breakage
of parts, mounting, and any other conditions that may affect its
operation. A guard or other parts that are damaged should be properly
repaired or replaced.

19. NEVER LEAVE MACHINE RUNNING UNATTENDED.

Turn power ’’OFF.’’ Don’t leave any tool running until it comes to a
complete stop.

Summary of Contents for 9999 ITM













Reviews: