INTRODUCTION
Congratulations on your purchase of this ultra high
resolution IR night vision camera that utilises the latest
Sony Effio Chip set. The camera provides high
definition
and stability, strong anti-jamming, rich and real colors.
Installation and
operation of this model are very straight-
forward, however please read this instruction manual
carefully to ensure proper use of the product.
CONNECTING
BRIEF OF PRODUCT
*
*
*
*
Sensor
((((
CCD
))))
Adopt SONY 1/3
"
EFFIO CCD Sensor.
*
*
*
*
Auto Gain Control (AGC)
Built-in auto gain control
(AGC)
circuit. The color camera
can get high definition picture in low Lux condition.
*
*
*
*
Scanning Mode
NTSC
or PAL
mode.
DC12V
Power Supply
Monitor
CIR42V
TROUBLE SHOOTING
Link wire rule
：
Power
Video
The symbol is intended to alert the user to the presence of
The symbol is intended to alert the user to the presence of
important operating and maintenance (servicing)
Instructions in the literature accompanying the appliance.
uninsulated ‘dangerous voltage’ within the product’s
enclosure
that may be of sufficient Magnitude to
constitute
a risk of electric shock to persons.
Video
DC12V
CAUTION:
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEA-
BLE PARTS INSIDE. REFER SERVICING TO OUALIFIED SERVICE
PERSONNEL.
RISK OF ELECTRIC. DO NOT OPEN
CAUTION:
TO PREVENT ELECTRIC SHOCKS AND RISK OF
FIRE HAZARD, DO NOT USE OTHER THAN A
SPECIFIED POWER SOURCE.
Note
MENU
UP
DOWN
RIGHT
LEFT
PRESS
TOGGLE SWITCH
OSD
SET
LENS
MANUAL/DC/VIDEO
EXPOSURE
SHUTTER
AUTO,FLK,1/50,1/250,1/500,1/2000,1/40000,
1/5000,1/10000,1/100000
BRIGHTNESS
0
－
255
AGC
LOW
/
MIDDLE
/
HIGH
/
OFF
D-WDR
OFF
/
ON(LEVEL:0-63)
RETURN
WHITE BAL ATW1/ATW2/AWC-SET/MANUAL:(INDOOR
、
OUTDOOR
、
MANUAL)
BACK
LIGHT
OFF
BLC:AREA SEL/AREA STATE/GAIN/HEIGHT/LEFT/RIGHT/
TOP/BOTTOM
HLC:LEVEL(0-255)/ MODE(ALL DAY/NIGHT ONLY)
DPC
COVER THE LENS THEN PRESS ENTER KRY
DAY &
NIGHT
COLOR
B/W
BURST(OFF/ON)/IR SMART(OFF/ON:IR GAIN/
HEIGHT/WIDTH/LEFT/RIGHT/TOP/ BOTTOM)/IR
LEVEL(HIGH/LOW)
AUTO
D-N(LEVEL/DELAY) /N-D(LEVEL/DELAY)
SPECIAL
CAM TITLE
ON
/
OFF
MOTION
OFF/ON
AREA SEL:AREA1-4
AREA STATE:OFF/ON
HEIGHT/WIDTH/LEFT/RIGHT/TOP/BOTTOM /
DEGREE/VIEW
PRIVACY
OFF/ON
AREA SEL:AREA1-8
AREA STATE:OFF/ON
HEIGHT/WIDTH/LEFT/RIGHT/TOP/BOTTOM /
COLOR
PARK.LINE
OFF/ON(LT/LB/RT/RB/F/N/T)
IMAGE ADJ
LENS SHAD:OFF/ON
2DNR:OFF/ON
MIRROR:OFF/ON
FONT COLOR:FONT(0-15)/ID&TITLE(0-15)
CONTRAST:0-255 SHARPNESS:0-31
NEG.IMAGE:OFF/ON
DISPLAY:CRT(PED LEVEL:0-63/COLOR GAIN:0-
255)/LCD(GAMMA:0-1/PED LEVEL:0-63/
COLOR:0-255)/USER(GAMMA:0-1/PED LEVEL:0-
63/COLOR:0-255)
RESET
FACTORY RESET
EXIT
1.
No picture after power-up
May be due to a power supply voltage abnormality - please check
voltage and polarity of connection. ( Warning - Reversing the
polarity upon connection will permanently damage the camera
and invalidate your warranty!)
2.
The picture has flowing interference ripples
May be caused by power supply AC ripples or video signal
interference due to ground loops
Check the monitor and peripheral equipment.
3.
The picture background colour changes continually
The electromagnetic file of fluorescent lamps can cause colour
roll. This is a recognised phenomenon with CCD cameras. Try to
increase the distance between the fluorescent and the camera
position to reduce the problem.
4.
Picture Smear
Can be caused by a power supply unstable voltage or maybe a
cable connection problem or high impedance.
!
Never point the camera directly at the sun as
it can damage the CCD sensor
Do not mount near a heater or radiator
!
Notes:
Please use the correct regulated low voltage power
Supply, ensuring the polarity is correct before connection
To avoid the possibility of damage due to lightning
please use an anti-surge device or turn off the power to
the camera during such conditions
