DC built-in battery electric screen User Manual
047-15xx
Install the screen in the location where the audience can see the whole
screen when it is fully extended.
The screen can be wall mounted or ceiling mounted/hanging, users can
choose the most suitable method according to their needs. Insure the
right equipment is used for whichever chosen method.
For wall mounting or ceiling mounting/hanging on a wooden surface, use
ø 4x50mm wood screws.
For wall mounting or ceiling mounting/hanging on a brick, concrete or
plaster surface, use ø 6x50mm screws with screw anchors or wall plugs.
Ceiling Hanging
Measure the distance between D-rings, drill holes for screw hooks the
same distance apart, making sure the holes is in line with each other and
parallel with the wall.
Screw the appropriate screw hooks into the holes and hang the screen
by the D-rings.
Ceiling method
Ceiling Mounting
Measure the distance from the holes in the end caps top surface, mark
out the same distance on the ceiling and drill holes for the screws, making
sure the holes are level. Screw an appropriate screw into each hole, hang
the screen from the screws with the holes in the end caps.
Wall Mounting:
(Unscrew the D-Rings if necessary)
Measure the distance from the holes in the wall mounting brackets, mark
out the same distance on the wall and drill holes for the screws, making
sure the holes are level. Screw an appropriate screw into each hole, hang
the screen from the screws with the holes in the brackets. Check the
screen is evenly spaced from the wall with a spirit level. (Screw
appropriate screws into the two bottom holes to fix the screen
ifnecessary)
controlled with remote control
controlled with product
Remark:
any intervention on the screen must be done by a professional
,if it is judged to be man-made damage
to the product,we are not responsible for it.
C
eiling mounting method
Wall mounting method
Product Electrical Specification
Installation Method
Product control mode and status indication
up
stop
down
set button
led
indicator
power
button
down stop up
上
Control Method
To extend the projection surface:
Press the
“down”button on the transmitter and
product, and the screen will fully extend till the
lower limit switch activates then stop .
To retract the projection surface:
Press the
“up” button on the transmitter and
product, and the screen will fully retract till the
upper limit switch activates then stop.
To stop the projection surface:
Press the
“stop” button on the transmitter and
product to stop the screen at desired position.
(note:please open the power button
firstly when operate the product)
Product
pairing
and limit adjustment
Press the button for three
seconds
，
the motor will turn
up and down one time.
Press the button for one
second
，
the motor will turn
up and down one time.
Pairing
process
complete.
Charger status display
Delete the stored
pairing
memory of any channel on receiver.
Press the button for ten
seconds
，
the motor will
turn up and down one
time.
1.Press the button for one
second
，
the motor will turn
up and down one time.
2.Press the button for ten
seconds
，
the motor will turn
up and down two times.
1.Deleted the stored
coding memory is
completed.
2.All settings deleted
successfully.
2.
Limit set and adjustment
Press the button
for one second
，
the motor will turn
up and down one
time, start the limit
setting state.
Press the button
for one second
，
the motor will turn
up and down one
time.
（
“up”button
is upper limit,
“down”button is
lower limit.)
Limit adjustment
completed.
Note:
：
when set the limit in the first time,please note
the lower limit need to be set for three times.
led indicator
red → in the charging
green → fully charged
led indicator
Remote control
pairing
Adjust it at desired
position and press
the button for one
second
，
the motor
will turn up and
down one time.
Rated voltage
：
14.8V
Rated power
：
36W
Rated current
：
3A
Battery capacity
：
3000mA
