Kikusui PFX2731S Operation Manual Download | Manualshive

Page: 46 / 54

background image

46

Operation Manual

PFX2731S

Specifications | General Specifications

Outline drawing

Unit: mm (inch)

6.

This is a Class I instrument. Be sure to ground this product's protective conductor terminal. The safety of this product
is guaranteed only when the product is properly grounded.

7.

Pollution is addition of foreign matter (solid, liquid or gaseous) that may produce a reduction of dielectric strength or
surface resistivity. Pollution Degree 2 assumes that only non-conductive pollution will occur except for an occasional
temporary conductivity caused by condensation.

MAX 440 (17.32)

430 (16.93)

MAX 440 (17.32)

430 (16.93)

MAX485 (19.09)

MAX15
(0.59)

MAX485 (19.09)

620 (24.41)

MAX 695 (27.36)

173 (6.81)

«
...
44
45
46
47
48
...
»

Summary of Contents for PFX2731S























































Reviews:

No comments

Related manuals for PFX2731S

Brand: T-Drill Pages: 75

Brand: Zeiss Pages: 38

Brand: ZOLL Pages: 5

Brand: Accu-Chek Pages: 3

Brand: iBin Pages: 2

Brand: Keithley Pages: 67

Brand: Keithley Pages: 23

Brand: Keithley Pages: 93

Brand: Oki Pages: 44

Brand: Magnescale Pages: 64

Brand: PANDROL Pages: 36

Brand: Badger Basket Pages: 7

Brand: Backyard Discovery Pages: 53

Brand: JB-Lighting Pages: 40

Brand: Backyard Play Systems Pages: 74

Brand: Macht Dental Pages: 8

Brand: M-Audio Pages: 12

Brand: M-Audio Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands