manualshive.com logo in svg

Kikusui BIM1000 Series, User Manual

Share
Download
Kikusui BIM1000 Series User Manual Download Page 73

BIM1000 Series

User’s Manual

73

Remote Control | Message Reference

Retrieving the most recent measured value

Queries the most recent measured value.

Example of retrieving measured values using :FETCh?

If :INITiate:CONTinuous

 (p. 72)

 is set to ON and :TRIGger:SOURce

 (p. 72)

 is set to EXTernal, when you 

send “*TRG” or SIGNAL I/O TRIG-IN signal or press SNGL TRG on the front panel, the product makes a 
single measurement. When you send :FETCh?, the measured value is read.

Executing a measurement and retrieving the measured value

When continuous measurement (:INITiate:CONTinuous) is off, a query for the measured value is made 
after executing a measurement once.
When the trigger source (:TRIGger:SOURce) is set to EXT, a measurement is not executed by this com-
mand alone. To execute a measurement, use SNGL TRG on the front panel or the SIGNAL I/O TRIG-IN 
signal (a measurement cannot be performed using *TRG).

Example of retrieving measured values using :READ?

If :INITiate:CONTinuous

 (p. 72)

 is set to OFF and :TRIGger:SOURce

 (p. 72)

 is set to INTernal, sending 

:READ? causes the measured value to be read after a measurement is made.
If :INITiate:CONTinuous

 (p. 72)

 is set to OFF and :TRIGger:SOURce

 (p. 72)

 is set to EXTernal, sending 

:READ? causes the product to switch to a trigger wait state. If you send a SIGNAL I/O TRIG-IN signal, the 
product makes a single measurement, and the measured value is read.

Program header

:FETCh?

Response

Any of the following responses will be returned depending on the :DATA:FORMat

 (p. 74)

 

setting.
Resistance only: <Resistance measurement (NR3)>
Voltage only: <Voltage measurement (NR3)>
Resistance and voltage: <Resistance measurement (NR3)>,<Voltage measurement 
(NR3)>

Unit

Ω, V

Note

When the measurement overflows, “+1.00000+E08” is returned. When a measurement 
error occurs, “+1.00000+E09” is returned.

Program header

:READ?

Response

Any of the following responses will be returned depending on the :DATA:FORMat

 (p. 74)

 

setting.
Resistance only: <Resistance measurement (NR3)>
Voltage only: <Voltage measurement (NR3)>
Resistance and voltage: <Resistance measurement (NR3)>,<Voltage measurement 
(NR3)>

Unit

Ω, V

Note

When continuous measurement (:INITiate:CONTinuous) is on, an execution error 
occurs.
The next command is not executed until the measurement is completed.
To execute this command after changing the measurement conditions, insert an interval 
of 100 ms.
When the measurement overflows, “+1.00000+E08” is returned. When a measurement 
error occurs, “+1.00000+E09” is returned.

Summary of Contents for BIM1000 Series































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands