manualshive.com logo in svg

Kikusui BIM1000 Series, User Manual

Share
Download
Kikusui BIM1000 Series User Manual Download Page 71

BIM1000 Series

User’s Manual

71

Remote Control | Message Reference

Trigger system

When triggers are used to make measurements, the product operation varies depending on the continu-
ous measurement function (:INITiate:CONTinuous) and trigger source (:TRIGger:SOURce).

Trigger flow chart

Continuous measurement (:INIT:CONT)

*1

*1.

This can only be set using a command.

ON

OFF

Trigger source
(:TRIG:SOUR)

INT

Performs continuously measurement.
(Trigger flow chart A)

Sending :INITiate or :READ? in the idle 
state 

*2

 applies a trigger. After outputting 

the measured value, the product returns 
to the idle state.
(Trigger flow chart B)

*2.

Trigger input is not accepted.

EXT

Sending *TRG or a TRIG-IN signal to the 
SIGNAL I/O connector or pressing SNGL 
TRG on the front panel applies a trigger. 
After the measurement is completed, the 
product changes to the trigger wait state.
(Trigger flow chart C)

Sending :INITiate or :READ? in the idle 
state 

*2

 causes the product to change to 

the trigger wait state. Sending *TRG 

*3

 or 

a TRIG-IN signal to the SIGNAL I/O con-
nector applies a trigger. After outputting 
the measured value, the product returns 
to the idle state.
(Trigger flow chart D)

*3.

If you send :READ? and the product changes to the trigger wait state, *TRG cannot be used.

Continuous 
measurement: ON

Trigger source: INTernal

Measurement output

Measurement

Computation

Delay

A

Continuous 
measurement: OFF

Trigger source: INTernal

Measurement output

Measurement

Computation

Delay

B

:INITiate/:READ?/

Idle state

Continuous 
measurement: ON

Trigger source: EXTernal

Measurement output

Measurement

Computation

Delay

C

TRIG-IN/*TRG/
SNGL TRG key

Trigger wait

Continuous 
measurement: OFF

Trigger source: EXTernal

Measurement output

Measurement

Computation

Delay

D

Trigger wait

Idle state

TRIG-IN/
*TRG

:INITiate

:READ?

TRIG-IN

Summary of Contents for BIM1000 Series































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands