manualshive.com logo in svg

KidKraft ASHBERRY, Installation And Operating Instructions Manual, Page: 46 / 76

Share
Download
KidKraft ASHBERRY Installation And Operating Instructions Manual Download Page 46

 46 

 

    

B: 

 Place 1 (2118) Front Trim tight to the top of (2124) Front Floor and flush to the outside edge of (2153) Post on 

the Swing Wall side.  Attach to (2153) Post with 4 (S2) #8 x 1-1/2” Wood Screws.  (fig. 16.3) 

C:

  Tight to top of (2124) Front Floor and tight to (2118) Front Trim attach 2 (2128) Siding to both (2153) Posts 

with 4 (S0) #8 x 7/8” Truss Screws per board. (fig. 16.3)  

D: 

 Install (2162) Siding - Clock followed by 4 more (2128) Siding making sure there are no gaps between boards. 

Attach to both (2153) Posts with 4 (S0) #8 x 7/8” Truss Screws per board.  The top of the last (2128) Siding should 

be tight to the bottom of (2125) Middle Front.   (fig. 16.3)

E:

  Tight to the siding and top of (2124) Front Floor attach a second (2118) Front Trim to (2153) Post with 4 (S2) 

#8 x 1-1/2” Wood Screws.  (fig 16.3)

Step 16:  Upper Front Wall Assembly

Part 2

28 x 

#8 x 7/8” Truss Screw

8 x 

#8 x 1-1/2” Wood Screw

Wood Parts

Hardware

6 x 

Siding 3/8 x 3-1/2 x 49-1/8”

1 x 

Siding - Clock 3/8 x 3-1/2 x 49-1/8”

2 x 

Front Trim 1 x 2 x 23-3/8”

2128

2118

S0

2162

S2

Fig. 16.3

x 4 per board

2153

Front Wall

2124

S2

S0

2118

Swing Wall

2125

x 4 per board

S2

x 4 per board

2128

2162

2118

Summary of Contents for ASHBERRY













































































Reviews:

No comments