manualshive.com logo in svg

KidKraft Appleton Play System F24148, Installation And Operating Instructions Manual

Share
Download
KidKraft Appleton Play System F24148 Installation And Operating Instructions Manual Download Page 26

 26 

C: 

 Attach 2 (0359) Front Dividers to (1762) Floor Back with 1 (H1) 1/4 x 1-1/2” Hex Bolt (with lock washer, flat 

washer and t-nut) per board. 

Be sure to keep bolts loose.

 (fig. 12.4 & 12.6)

D: 

 Attach each (0359) Front Divider to (1758) Top Back using 1 (PB2) 1/4 x 1-1/4” Pan Bolt (with lock washer, flat 

washer and t-nut) per board. 

Be sure to keep bolts loose.

 (fig. 12.4 & 12.5)

E:  

Level and attach (1758) Top Back to both (1771) Posts using 4 (S7) #12 x 2” Pan Screws (with 3/16” flat 

washers). (fig. 12.7) 

Step 12: Floor Back Assembly cont.

PB2

H1

x 2

Loosely 

attach 

bolts

Fig. 12.4

Fig. 12.5

Fig. 12.6

Fig. 12.7

S7

Hardware

4 x 

 #12 x 2”  Pan Screw (with 3/16” flat washer)

2 x 

 1/4 x 1-1/2” Hex Bolt 

 

(1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

2 x 

1/4 x 1-1/4” Pan Bolt 

 

(1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

S7

H1

PB2

1 x 

Top Back 1 x 4 x 38-1/2”

2 x  

Front Divider 1 x 4 x 38”

Wood Parts

Hole towards top

1758

1771

1762

1771

0359

1758

0359

S7

1762

1758

1771

1771

PB2

PB2

H1

H1

1758

0359

Summary of Contents for Appleton Play System F24148









































Reviews:

No comments

Brands by name

Popular brands

Load more brands