DC Jack
Getting Started
Installing the Batteries
NOTE: This unit can operate on either battery or
optional AC adaptor. While the AC adaptor is
plugged in, the batteries will not be used.
ATTENTION:
AC adaptor and batteries should only be
installed by an adult.
Use a Phillips screwdriver to open the battery
compartment door located on the bottom of the unit.
Install 6 C size batteries, making sure that the + and
– polarities match the diagram printed inside the
battery compartment.
Close the battery compartment door and tighten
the battery door screw. Do not over-tighten.
For the Best Possible Performance
• We recommend the use of alkaline batteries for longer
life.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium) batteries.
• Batteries are to be inserted with correct polarity.
• Remove exhausted batteries from the unit.
• Do not attempt to recharge non-rechargeable
batteries.
• Remove the rechargeable batteries from the unit
before charging.
• The supply terminals are not to be short-circuited.
• Batteries should be removed if the item is operating
using the optional AC adapter or will not be used for
an extended period of time, such as a month or
longer, to prevent battery leakage or damage.
• Rechargeable batteries should only be charged under
adult supervision.
• Only batteries of the same or equivalent type as
recommended are to be used.
Unpacking and Setup
1. Remove the product and all packing materials from
the carton.
2. It is a good idea to save the packing materials in case
the unit needs to be returned for service. If you do
dispose of the packing materials, please do so
properly.
3. Remove any feature labels, fact tags, or clear
protective films from the front or top of the unit, if
applicable. Do not remove any warning labels from
the back or bottom of the unit.
4. The unit should be placed on a level surface, away
from direct sunlight, and away from the sources of
excess dust, dirt, heat, water, moisture, vibration, and
strong magnetic fields.
5. Protect your furniture when placing the unit on natural
wood or wood with a lacquered or coated finish. A
cloth or other protective material should be placed
between the unit and the furniture.
Optional AC Adaptor Installation
NOTE:The AC adaptor should only be connected by
an adult.
• Connect a DC 9V 1.5A, center positive AC adaptor (not
included) into the DC Jack located on the back of the
unit, then plug the AC adaptor into an outlet.
Playing and Charging your iPod
Playing your iPod
1. Gently dock iPod in Dock (see directions at left).
2. Press
Button
to turn unit on.
3. Press the
Button
to play iPod, and again to pause.
4. Press Volume UP or DOWN
Buttons
to adjust
volume to desired level.
5. Press the or
Button
to go to the next or previous
track on your iPod. Press and hold for high speed search
within the track playing.
6. When you are done listening, remember to turn the unit
off (press
Button
).
TIP: You can also turn off the unit by undocking your playing
iPod.
Charging your iPod
1. Connect the unit to an optional 9V/1.5A AC adaptor to
charge your iPod.
Unit will not charge iPod when
operating on batteries.
When docked and the PF-415 is connected to an outlet with
an AC adaptor, your iPod will charge until fully charged. Unit
will not overcharge iPod.
Skip/Search
Backward Button
Skip/Search
Forward Button
Back View
PF415 IB_back Printing color: Black APIRL 13, 2012
size: 355 x 240
Docking your iPod
1. Tilt cover back all the way to expose iPod dock.
2. Gently dock your iPod to the 30-pin connector.
3. Gently tilt cover forwards so it supports your
iPod.
NOTE: DO NOT FORCE COVER TOO FAR
FORWARD WHEN iPod IS DOCKED
Doing so may damage the dock or your iPod.
iPod dock
Cover
Play/Pause Button
Volume Down Button
Power On/Off Button
Volume Up Button
Battery Installation
(bottom of unit)
