Kidde 151FE1, Installation, Operation & Maintenance Manual

Page: 11 / 16

06-235793-001 December 2001
Scorpio
™
7
TECHNICAL SPECIFICATIONS
Input Power:
• 120 Vac, 50/60 Hz 0.5 A max.
• 240 Vac, 50/60 Hz 0.25 A max.
An impedance of 25K ohms from any field wiring terminal
to ground except AC input power and relay outputs will
cause a ground fault condition.
Panel 24 VDC Power Requirements:
• Standby Current: 35mA
• Alarm Current: 200mA
Auxiliary Power:
• 24 Vdc at 0.25A in alarm only
Output Circuit:
• One Style-Y signal circuit, 10K ohm EOL.
• Rated at 24 Vdc 0.5 A (max)
• Open circuit fault impedance: 13.5K ohms
• Short circuit fault impedance: 4.5K ohms
When programmed for two-zone operation, pulses on first
alarm, steady output on second alarm.
Relay Outputs:
• Alarm 1 relay (activates on 1st zone in alarm)
• Alarm 2 relay (activates on 2nd zone in alarm or
start of release)
Note: When set up is for a single zone release, S1=ON,
Alarm 1 and Alarm 2 relays will both activate on
first alarm.
• Trouble relay (normally energized)
• All are Form C, rated 2A @ 250 Vac/30 Vdc
Note: For ULC installations, the form C relays are rated
for 120 V AC (150 V max to ground).
Release Output, Solenoid Style
Output circuit capable of activating 2 of the following con-
trol heads P/Ns:
• 48650001
• 890181
• 899175
Output held ON for 90 seconds. Circuit is power limited
and supervised on terminals 28-31.
• Open circuit fault impedance: 1.7K ohms
UL Compatibility Identifier Number: C30FE1
Two Detection Circuits:
Output voltage: 17.3 - 26.0 Vdc
Max. number of 2 wire smoke detectors per circuit: 15
Maximum line resistance: 50 Ohms
Operation: Style B, 10K ohm EOL.
See Table 1 for 2-wire detector compatibility
• Open curcuit fault impedance: 22K ohms
Auxiliary Inputs:
• Supervisory Input, Style B, 10K ohm EOL.
• Manual Release Input, Style B, 10K ohm EOL.
• Abort Input, Style B, 10K ohm EOL.
• Open circuit fault impedance for Abort, Supervisory
and Manual release: 22K ohms
Isolation Switch:
Disconnects the release output. Available by cutting jump-
ers W1 and W2.
Standby Batteries:
Requires (2) 12 Vdc 1.2A-H sealed lead acid batteries for
24 hour standby operation/5 minute alarm operation at
maximum rated load. Order separately.
Battery Charger Output:
• Nominal Standby Load: 35 mA
• Maximum Charging Current 0.48 A
Time Delay to Discharge:
0, 10, 20, 30, 40, 50, or 60 seconds field selectable.
Dimensions (nominal): 13.25”H x 11.0”W x 2.30”D
ORDERING INFORMATION
DESCRIPTION PART NO.
Scorpio Control Panel 84-232000-102
Above panel (240 Vac input) 84-232000-104
(1) Battery 12 Vdc 1.2 A-H 06-115915-020
Accessory Kit (50 10K EOL resistors) 06-129520-001
Extra Operating Instruction Sheet 06-235883-001
Spare Scorpio Circuit Board 06-129800-002
Extra Scorpio Key 06-118013-001
Canadian Scorpio 84-232000-202
Canadian Scorpio (240 Vac Input) 84-232000-204
firealarmresources.com