background image

In U.S.A.

 

 

4902 Hammersly Rd.

2016

 

Madison, WI 53711

Customer Service:

 

877-741-6154 

[email protected] 

www.kidtraxtoys.com

9

21

Warning:

 Any changes or modifications to this unit not expressly approved by the party 

responsible for compliance could void the user's authority to operate the equipment.

 

NOTE:

 This equipment has been tested and found to comply with the limits for a Class B 

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide 

reasonable protection against harmful interference in a residential installation. 

This equipment generates, uses and can radiate radio frequency energy and, if not 

installed and used in accordance with the instructions, may cause harmful interference 

to radio communications. However, there is no guarantee that interference will not 

occur in a particular installation. If this equipment does cause harmful interference to 

radio or television reception, which can be determined by turning the equipment off 

and on, the user is encouraged to try to correct the interference by one or more of the 

following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different 

from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

 

10

FCC  Information 

Summary of Contents for Disney MINNIE KT1123

























Reviews: