background image

6

OPERATION

Automatic Turn-On Selection:

 The KX series offers three different automatic turn-on modes that can be 

selected on the end panel; +12V, DC Offset, and Audio. Using either the DC Offset or Audio mode causes the 
REM terminal to have +12V out for turning on additional amplifi ers.

•  

Remote Turn-On: Set the switch to +12V to use the remote turn-on lead from your source unit. Run 18 
gauge wire from the Remote Turn-On Lead on your source unit to the terminal labeled REM between the 
amplifi er’s positive and negative power terminals. This is the preferred automatic turn-on method. 

•  

DC Offset Turn-On: If Remote Turn-On is not an option, the next best setting is DC Offset. The DC Offset 
mode detects a 6V DC offset from the HI-Level speaker outputs when the source unit has been turned on.

•  Signal Sense Turn-On: The Audio setting is the fi nal alternative for Automatic turn-on. This is a Signal Sense 

turn-on method that detects the incoming audio signal from your source unit and automatically turns on the 
amp. This turn-on method will not work properly if the input gain control is not set appropriately.

Input Level:

 The RCA inputs on KICKER KX amplifi ers are capable of receiving either Hi or Low-level signals 

from your source unit. If the only output available from your source unit is a Hi-Level signal, simply press in the 
Input Level switch on the amplifi er. Either input method will provide a low-level output signal at the RCA output, 
which effectively passes the audio signal to another amplifi er or component. Refer to the wiring section of this 
manual for additional instructions.

Input Gain Control:

 The input gain control is not a volume control. It matches the output of the source unit to 

the input level of the amplifi er. Turn the source unit up to about 3/4 volume (if the source unit goes to 30, turn it 
to 25). Next, slowly turn (clockwise) the gain on the amplifi er up until you can hear audible distortion, then turn it 
down a little.

Crossover Switches with Frequency Multiplier:

 Use the XOVER switches on the end panel of the amplifi er 

to set the internal crossovers of AMPS 1 & 2 to OFF, HI-PASS, LO-PASS, or BAND-PASS (AMP 2 only). When 
the switch is set to 

OFF

, a full bandwidth signal will be amplifi ed. Set the switch to 

HP

 if you want the amplifi er’s 

internal crossover to serve as a high-pass fi lter. Set the switch to 

LP

 if you want the amplifi er’s internal crossover 

to serve as a low-pass fi lter. Set the switch to 

BP

 when a specifi c frequency range is required. Never change the 

crossover switches with the audio system on!

Set the 

1X/10X

 frequency multiplier switch to the setting that is appropriate for your application. A setting of 

10X

 will set the range of the 

AMP 1

 crossover to 100–5,000Hz, and the LO-PASS crossover of 

AMP 2

 to 

400–5,000Hz.

KICK EQ Bass Boost Control:

 The variable bass boost control on the side of the KX400.4 amplifi er is 

designed to give you increased output, 0–18dB, at 40Hz. The setting for this control is subjective. If you turn it 
up, you must readjust the input gain control to avoid clipping the amplifi er.

Mini-USB for internal use only; do NOT remove or tamper. KICKER is not responsible for any 
damage to equipment resulting from connections made to this port.

2013 KX 4-Channel Amps Rev C.indd   6

2013 KX 4-Channel Amps Rev C.indd   6

10/24/2012   4:31:57 PM

10/24/2012   4:31:57 PM

Summary of Contents for KX400.4

































Reviews: